Supplemental Characteristics | TDK 750W, 1500W guide

NOTES:

*1: Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage.

*2: Minimum current is guaranteed to maximum 0.4% of the rated output current.

*3: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be de- scribed as 100-240Vac (50/60Hz).

*4: At 100/200V input voltage and maximum output power.

*5: From 85132Vac or 170265Vac, constant load.

*6: From No-load to Full-load, constant input voltage. Measured at the sensing point in Remote Sense.

*7: For load voltage change, equal to the unit voltage rating, constant input voltage.

*8: For 6V models the ripple is measured at 26V output voltage and full output current. For other models, the ripple is measured at 10100% output voltage and full output current.

*9: With rated, resistive load.

*10. For 6300V models: Measured with JEITA RC-9131A (1:1) probe For 600V model: Measured with (10:1) probe.

2.12 SUPPLEMENTAL CHARACTERISTICS

The supplemental characteristics give typical but non-warranted performance characteristics. The supplemental characteristics are useful in assessing applications for the power supply. Several kinds of supplemental characteristics are listed below.

1.Evaluation Data: Typical performance of the power supply.

2.Reliability Data: Reliability Performance of the power supply.

3.IEC1000 Data: Performance of the power supply under IEC1000 test conditions.

4.EMI Data: Typical EMI (conducted and radiated) performance of the power supply.

The supplemental characteristics data is held in each TDK-Lambda Americas Inc. sales and service facility. For further details please contact the TDK-Lambda Americas Inc. office nearest you.

11

83-507-013 Rev. D

Image 19

TDK 750W, 1500W technical manual Supplemental Characteristics

Contents

Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Trademark Information Limitation of WarrantyWarranty Service Disclaimer Safety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Anderungen and Bauteileersatz Sicherheits-und WarnsymboleUmweltbedingungen General Description Features and optionsGeneral Information Introduction Parallel operation Multiple output power systemControl via the serial communication port Analog voltage programming and monitoring Accessories Chapter Specifications Vout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Initial Inspections InstallationGeneral Preparation for USE Rack Mount Slides optional AC Input Power ConnectionLOCATON, Mounting and Cooling AC Source Requirements AC Input Cord AC Input Connector, 1500W modelsAC Input Connector, 750W models AC Input Wire Connection, 1500W models General TURN-ON Checkout ProcedurePrior to Operation UVL Check Constant Voltage CheckConstant Current Check OVP Check Connecting the Load AWG Wire termination Inductive loads Noise and Impedance EffectsMaking the load connections 6V to 60V Models 80V to 600V Models Wire terminal lug 2 places Load wires connection to the output connector Connecting single loads, remote sensing Connecting single loads, local sensing defaultConnecting multiple loads, radial distribution method Grounding outputs Multiple load connection with distribution terminals Local sensing Sense wiringOutput Terminal Grounding Local and Remote Sensing Remote sensing 10.4 J2 sense connector technical information Front Panel Controls and Indicators Front and Rear Panel Controls and Connectors Auxiliary Function Rear panel connections and controls Rear Panel Connections and Controls Rear Panel SW1 Setup Switch 1 SW1 position function Resetting the SW1 switch Making J1 connections Rear Panel J1 Programming and Monitorng Connector Local SignalEnain Ifcom Constant Current Mode Constant Voltage ModeLocal Operation Automatic Crossover Setting the OVP levelResetting the OVP circuit Over Voltage Protection OVP Output ON/OFF Control Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Foldback Protection CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorPsok Signal Safe-start mode Over Temperature Protecton OTPLast Setting Memory Auto-restart mode Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Parallel Operation Connection to the load Advanced parallel configurationSetting the units as Master or Slave Master and Slave units default operation Current display accuracy To release units from Slave modeAST OFF *OUT OFF Locked front panel DAISY-CHAIN ConnectionFront Panel Locking Unlocked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control 6 RS232/RS485 port in Local mode Rear Panel RS232/RS485 ConnectorFront panel in Remote mode MD Mode SRQ Retransmission MD Mode Option Factory Installed MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages ID Control Commands Initialization Control CommandsOutput Control Commands OUT? DVC?Filter FILTER? Global Output Commands Enable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Disable SRQ retransmission MD Mode Option Required Addressed commands without response Acknowledge SRQ Addressed commands with response Read registersPrint Power On Time Test if MD Mode is Installed 1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range 10.6 Status Control Commands STATUS, Error and SRQ Registers Status Registers Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Serial Communication Test SET-UP Power supply set-upCommunication Test PPM/C SpecificationsIsolated Analog Programming Option 1 0-5V/0-10V Option PN IS510 Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating