Isolated Analog Programming Option, Specifications | TDK 1500W

CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION

8.1 INTRODUCTION

Isolated Analog Programming is an internal Option Card for analog programming of the GenesysTM power supply series. The option is factory installed and cannot be obtained with a GPIB (IEEE-488) Interface. Output Voltage and Output Current can be programmed and readback through optically iso- lated signals which are isolated from all other ground references in the power supply.

There are two types of Isolated Analog programming cards:

1.0-5V/0-10V option (PN: IS510): Using 0-5V or 0-10V signals for programming and readback.

2.4-20mA option (PN: IS420): Using current signals for programming and readback.

8.2SPECIFICATIONS

8.2.10-5V/0-10V OPTION (PN: IS510)

Programming	Output Voltage programming accuracy	%	+/-1
Inputs	Output Current programming accuracy	%	+/-1
	Output Voltage programming temperature coefficient	PPM/°C	+/-100
	Output Current programming temperature coefficient	PPM/°C	+/-100
	Input impedance	Ohm	1M
	Absolute maximum voltage	Vdc	0-15
	Max. voltage between program inputs and supply outputs	Vdc	600
Monitoring	Output Voltage monitoring accuracy	%	+/-1.5
Outputs	Output Current monitoring accuracy	%	+/-1.5
	Output Impedance (see Note)	Ohm	100
	Max. voltage between monitoring outputs and supply outputs	Vdc	600

NOTE:

Use 100Kohm minimum input impedance for the monitoring circuits to minimize the readback error.

8.2.24-20mA option (PN: IS420)

Programming	Output Voltage programming accuracy	%	+/-1
Inputs	Output Current programming accuracy	%	+/-1
	Output Voltage programming temperature coefficient	PPM/°C	+/-200
	Output Current programming temperature coefficient	PPM/°C	+/-200
	Input impedance	Ohm	50
	Absolute maximum input current	Vdc	0-30
	Max. voltage between program inputs and supply outputs	Vdc	600
Monitoring	Output Voltage monitoring accuracy	%	+/-1.5
Outputs	Output Current monitoring accuracy	%	+/-1.5
	Maximum load impedance	Ohm	500
	Max. voltage between monitoring outputs and supply outputs	Vdc	600

68

83-507-013 Rev. D

Image 76

TDK 1500W, 750W technical manual Isolated Analog Programming Option, Specifications, 1 0-5V/0-10V Option PN IS510, Ppm/C

Contents

Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Limitation of Warranty Warranty ServiceDisclaimer Trademark Information Safety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Anderungen and Bauteileersatz Sicherheits-und WarnsymboleUmweltbedingungen Features and options General InformationIntroduction General Description Multiple output power system Control via the serial communication portAnalog voltage programming and monitoring Parallel operation Accessories Specifications Chapter Vout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Installation GeneralPreparation for USE Initial Inspections AC Input Power Connection LOCATON, Mounting and CoolingAC Source Requirements Rack Mount Slides optional AC Input Connector, 1500W models AC Input Connector, 750W modelsAC Input Wire Connection, 1500W models AC Input Cord General TURN-ON Checkout ProcedurePrior to Operation Constant Voltage Check Constant Current CheckOVP Check UVL Check Connecting the Load Wire termination AWG Inductive loads Noise and Impedance EffectsMaking the load connections 6V to 60V Models Wire terminal lug 2 places 80V to 600V Models Load wires connection to the output connector Connecting single loads, remote sensing Connecting single loads, local sensing defaultConnecting multiple loads, radial distribution method Multiple load connection with distribution terminals Grounding outputs Sense wiring Output Terminal GroundingLocal and Remote Sensing Local sensing 10.4 J2 sense connector technical information Remote sensing Front and Rear Panel Controls and Connectors Front Panel Controls and Indicators Auxiliary Function Rear Panel Connections and Controls Rear panel connections and controls Rear Panel SW1 Setup Switch Resetting the SW1 switch 1 SW1 position function Rear Panel J1 Programming and Monitorng Connector Making J1 connections Signal EnainIfcom Local Constant Current Mode Constant Voltage ModeLocal Operation Setting the OVP level Resetting the OVP circuitOver Voltage Protection OVP Automatic Crossover Output SHUT-OFF SO Control VIA Rear Panel J1 Connector Under Voltage Limit UVLFoldback Protection Output ON/OFF Control CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorPsok Signal Over Temperature Protecton OTP Last Setting MemoryAuto-restart mode Safe-start mode Series Operation Series connection for increased output voltage Series connection for positive and negative output voltage Series connection for positive/negative output voltages Parallel Operation Advanced parallel configuration Setting the units as Master or SlaveMaster and Slave units default operation Connection to the load Current display accuracy To release units from Slave modeAST OFF *OUT OFF DAISY-CHAIN Connection Front Panel LockingUnlocked front panel Locked front panel Remote Analog Programming LOCAL/REMOTE Analog Indication Down Remote voltage programming connection Resisitive Programming of Output Voltage and Current Limit Remote resistive programming Remote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control Configuration 6 RS232/RS485 port in Local mode Rear Panel RS232/RS485 ConnectorFront panel in Remote mode MD Mode Option Factory Installed MD Mode Description MD Mode enable Serial communication modeMD Mode SRQ MD Mode SRQ Retransmission Connecting Power Supplies to RS232 or RS485 BUS Single power supply Communication Interface Protocol Error Messages Command SET Description ID Control Commands Initialization Control CommandsOutput Control Commands DVC? FilterFILTER? OUT? Global Output Commands Single Byte Commands Enable MD Mode MD Mode Option RequiredDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option Required Addressed commands with response Read registers Print Power On TimeTest if MD Mode is Installed Addressed commands without response Acknowledge SRQ 1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range STATUS, Error and SRQ Registers 10.6 Status Control Commands Conditional Registers Status Registers Service Request Enable and Event Registers BIT Fault Enable Register Fault Event Register Status Enable Register Status Event Register Serial Communication Test SET-UP Power supply set-upCommunication Test Specifications Isolated Analog Programming Option1 0-5V/0-10V Option PN IS510 PPM/C Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP