Manuals / Brands / Computer Equipment / Power Supply / TDK / Computer Equipment / Power Supply

TDK 1500W, 750W CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS

1 80

Download 80 pages, 1.61 Mb

83

-

507

-

013 Rev. D

27

CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS

4.1 INTROD

UCTION

The Genesys

TM

Power Supply series has a full set of controls, indicators and connectors that allow the

user to easily setup and operate the unit. Before starting to operate the unit, please read the fo

l

lowing

Sections for explanation of the function

s of the controls and connectors terminals.

-

Section 4.2: Front Panel Controls and Indicators.

-

Section 4.3: Rear Panel Connections and Controls.

4.2 FRONT PANEL CONTROLS AND INDICATORS

See Fig.4

-

1 to review the controls, indicators and meters located on

the power supply front panel.

Table 4

-

1: Front Panel controls and indicators

Nu

m

ber

Control/Indicator

Description

Section

1

VOLTAGE control

High resolution rotary encoder for adjusting the Output

Voltage. Also adjusts the OVP/UVL levels and selects the

A

d

dress

5.2.1

5.3.1

5.4.1

7.2.2

2

VOLTAGE indicator

Green LED, lights for constant

-

Voltage mode oper

a

tion.

3

VOLTAGE display

4 digit, 7

-

segment LED display. Normally displays the Ou

t-

put Voltage. When the PREV button is pressed, the display

indicates th

e programmed setting of the Output Voltage.

When the OVP/UVL button is pressed, the Voltage display

ind

i

cates the OVP/UVL setting.

Fig.4-1: Front panel controls and indicator s

VOLTAGE

ALARM

FINE

PREV/

OVP

UVL

FOLD

REM/LOC

OUT

DCAMP S

CURRENT

DCVOLTS

POWER

1

14

17

18

19

2

15

16

3

13

10

4

11

5

12

9

6

7

8

Contents

Main GENESYS 750W/1500W - TDK Programmable DC Power Supplies Page Page Page Page Page Page TAB LE OF CONTENTS 83 F 1 WARRANTY LIMITATION OF WARRANTY WARRANTY SERVICE DISCLAIMER TRADEMARK INFORMATION SAFETY INSTRUCTIONS CAUTION INSTALLATION CATEGORY GROUNDING FUSES SAFETY INSTRUCTIONS ENVIRONMENTAL CONDITIONS SICHERHEITS - INSTALLATIONS ANWEISUNGEN Page CHAPTER 1 GENERAL INF 6 ORMATION 1.1 USER MANUAL CONTENT 1.2 INTRODUCTION Page 8 1.3 ACCESSORIES CHAPTER 2 SPECIFICATIONS mA Vout: 4 digits,accuracy:0.5%of rated current +1 count 4 digits,accuracy:0.5%of rated voltage+ 1 count Re-startmodes(AutoRestart, SafeStart) Baudrateselection:1200, 2400,4800, 9600and 19200 Page Page CHAP 13 TER 3 INSTALLATION 3.1 GENERAL 3.2 PREPARATION FOR USE 14 mount slides assembly 1: Rack Fig. 3 3.5 LOCATON, MOUNTING AND COOLING Fig.3-2: Stripped Wires installed in Strain Relief 16 3.8 TURN (Phoenix) Plug P/N: MC1,5/5-ST-3,81 Fig.3-4: J2 Sense connector default conn ection Page 18 3.9 CONNECTING THE LOAD Page Page Page Page +L + +L + 24 +L + 25 OUTPUT TERMINAL GROUNDING 3.10 LOCAL AND REMOTE SENSING Fig.3-14: J2 Sense connector location Page 27 CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS Table 4 the power supply front panel. 1 to review the controls, indicators and meters located on See Fig.4 Page 29 4.3 REAR PANEL CONNECTIONS AND CONTROLS Fig.4-2: Rear panel connections and controls 30 4.4 REAR PANEL SW1 SETUP SWITCH Fig.4-3: SW1 setup DIP-switch 4.4.2 aded screwdriver to change the SW1 switch setting. bl Off. Then use any small flat 32 4.5 REAR PANEL J1 PROGRAMMING AND MONITORNG CONNECTOR Page CHAPTER 5 LOCAL OPERATION 35 5.3 OVER VOLTAGE PROTECTION (OVP) 36 OUTPUT SHUT 5.7 5.6 5.5 37 5.8 2 for The SO control logic can be selected by the rear panel SW1 Setup switch. Refer to Table 5 solated from the power supply output. 38 START AND AUTO 5.11 SAFE RESTART MODES 5.12 OVER TEMPERATURE PROTECTON (OTP) 39 5.14 SERIES OPERATION Page 41 5.15 PARALLEL OPERATION Page Page 44 5.17 FRONT 5.16 DAISY CHAIN CONNECTION PANEL LOCKING CHAPTER 6 REMOTE ANALOG PROGRAMMING 6.2 LOCAL/REMOTE AN 6.1 INTRODUCTION ALOG INDICATION 6.3 LOCAL/REMOTE ANALOG INDICATION 46 6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND OUTPUT CURRENT 47 6.5 RESISITIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT 48 6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT 49 CHAPTER 7 RS232 & RS485 REMOTE CONTROL 7.1 INTRODUCTION 7.2 CONFIGURATION 50 7.3 REAR PANEL RS232/RS485 CONNECTOR Page 52 7.5 CONNECTING L=2m typ. L=2mtyp. Fig.7-3: RS232 cable with DB9 con nector (P/N: GEN/232-9) 53 7.6 COMMUNICATION INTERFACE PROTOCOL 54 7.7 ERROR MESSAGES 7.8 COMMAND SET DESCRIPTION Page Page 57 7.9 GLOBAL OUTPUT COMMANDS 58 7.10 SINGLE BYTE COMMANDS Page Page GEN750W model s program the power supply over the rated values. The power supply can accept values higher 5% than the table values, howeverit is not rec ommended to 4: Current programming range 62 7.11 STATUS, ERROR AND SR Q REGISTERS Status Registers Serial Fig.7-7: Status and Error Registers D iagram 9 for the Status Condition register bits. tion Register bits and Table 7 i Cond 7.11.2 Conditional Registers (continued) 7.11.3 r Remote mode. will be generated either in Local o The SRQ message is: Inn terminated by CR, where the nn is the power supply address. The SRQ Page Page 67 7.12 SERIAL COMMUNICATION TEST SET UP 68 CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION 8.2 SPECIFICATION 8.1 INTRODUCTION S 69 8.3 ISOLATED PROGRAMMING & MONITORING CONNECTOR 70 8.4 SETUP AND OPERATING INSTRUCTIONS 71 CHAPTER 9 MAINTENANCE 9.5 PARTS REPLACEMENT AND REPAIR 9.2 UNIT 9.1 INTRODUCTION S UNDER WARRANTY 72 9.7 FUSE RATING