TABLE OF CONTENTS
5.15.1 Basic parallel operation…………………………………………………………………… | Pg. 41 |
5.15.2 Advanced parallel operation……………………………………………………………… | Pg. 42 |
5.16 | Pg. 45 |
5.17 FRONT PANEL LOCKING………………………………………………………………………. | Pg. 44 |
5.17.1 Unlocked front panel……………………………………………………………………… | Pg. 44 |
5.17.2 Locked front panel………………………………………………………………………… | Pg. 44 |
CHAPTER 6 REMOTE ANALOG PROGRAMMING……………………………………………… | Pg. 45 |
6.1 INTRODUCTION…………………………………………………………………………………… | Pg. 45 |
6.2 LOCAL/REMOTE ANALOG CONTROL………………………………………………………… | Pg. 45 |
6.3 LOCAL/REMOTE ANALOG INDICATION………………………………………………………. | Pg. 45 |
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT……….. | Pg. 46 |
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT………………….. | Pg. 47 |
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT………………………... | Pg. 48 |
CHAPTER 7 RS232 & RS485 REMOTE CONTROL……………………………………………... | Pg. 49 |
7.1 INTRODUCTION…………………………………………………………………………………… | Pg. 49 |
7.2 CONFIGURATION…………………………………………………………………………………. | Pg. 49 |
7.2.1 Default setting………………………………………………………………………………... | Pg. 49 |
7.2.2 Address setting………………………………………………………………………………. | Pg. 49 |
7.2.3 RS232 or RS485 selection…………………………………………………………………. | Pg. 49 |
7.2.4 Baud rate setting…………………………………………………………………………….. | Pg. 49 |
7.2.5 Setting the unit into Remote or Local mode………………………………………………. | Pg. 49 |
7.2.6 RS232/458 port at Local mode…………………………………………………………….. | Pg. 50 |
7.2.7 Front panel in Remote mode………………………………………………………………. | Pg. 50 |
7.3 REAR PANEL RS232/485 CONNECTOR………………………………………………………. | Pg. 50 |
7.4 MD MODE OPTION (Factory Installed)…………………………………………………………. | Pg. 51 |
7.4.1 MD Mode Description………………………………………………………………………. | Pg. 51 |
7.4.2 MD Mode enable - Serial communication mode…………………………………………. | Pg. 51 |
7.4.3 MD Mode SRQ………………………………………………………………………………. | Pg. 51 |
7.4.4 Communication Collisions………………………………………………………………….. | Pg. 51 |
7.4.5 MD Mode SRQ Retransmission…………………………………………………………… | Pg. 51 |
7.5 CONNECTING POWER SUPPLIES TO RS232 OR RS485 BUS……………………………. | Pg. 52 |
7.5.1 Single power supply…………………………………………………………………………. | Pg. 52 |
7.5.2 Multi power supply connection to RS232 or RS485 BUS……………………………….. | Pg. 53 |
7.6 COMMUNICATION INTERFACE PROTOCOL………………………………………………… | Pg. 53 |
7.6.1 Data format…………………………………………………………………………………... | Pg. 53 |
7.6.2 Addressing…………………………………………………………………………………… | Pg. 53 |
7.6.3 End of message…………………………………………………………………………….. | Pg. 53 |
7.6.4 Command repeat……………………………………………………………………………. | Pg. 53 |
7.6.5 Checksum……………………………………………………………………………………. | Pg. 53 |
7.6.6 Acknowledge…………………………………………………………………………………. | Pg. 53 |
7.6.7 Error message……………………………………………………………………………….. | Pg. 54 |
7.6.8 Backspace……………………………………………………………………………………. | Pg. 54 |
7.7 ERROR MESSAGES……………………………………………………………………………… | Pg. 54 |
7.8 COMMAND SET DESCRIPTION………………………………………………………………… | Pg. 54 |
7.8.1 General guides………………………………………………………………………………. | Pg. 54 |
7.8.2 Command set categories…………………………………………………………………… | Pg. 54 |
7.8.3 Initialization control commands…………………………………………………………….. | Pg. 55 |
7.8.4 ID control commands……………………………………………………………………….. | Pg. 55 |
7.8.5 Output control commands………………………………………………………………….. | Pg. 55 |
7.9 GLOBAL OUTPUT COMMANDS……………………………………………………………….. | Pg. 57 |
7.9.1 General……………………………………………………………………………………….. | Pg. 57 |
7.10 SINGLE BYTE COMMANDS…………………………………………………………………… | Pg. 58 |
7.10.1 General……………………………………………………………………………………… | Pg. 58 |
7.10.2 Global commands without response…………………………………………………….. | Pg. 58 |
7.10.3 Global commands with response………………………………………………………… | Pg. 59 |
7.10.4 Addressed commands with response…………………………………………………… | Pg. 59 |
7.10.5 Addressed commands without response……………………………………………….. | Pg. 59 |
