Main
GENESYS
750W/1500W
-
TDK
Programmable DC Power Supplies
Page
Page
Page
Page
Page
Page
TAB
LE OF CONTENTS
83
F
1
WARRANTY
LIMITATION OF WARRANTY
WARRANTY SERVICE
DISCLAIMER
TRADEMARK INFORMATION
SAFETY INSTRUCTIONS
CAUTION
INSTALLATION CATEGORY
GROUNDING
FUSES
SAFETY INSTRUCTIONS
ENVIRONMENTAL CONDITIONS
SICHERHEITS
-
INSTALLATIONS ANWEISUNGEN
Page
CHAPTER 1 GENERAL INF
6
ORMATION
1.1 USER MANUAL CONTENT
1.2 INTRODUCTION
Page
8
1.3 ACCESSORIES
CHAPTER 2 SPECIFICATIONS
mA
Vout:
4 digits,accuracy:0.5%of rated current +1 count
4 digits,accuracy:0.5%of rated voltage+ 1 count
Re-startmodes(AutoRestart, SafeStart)
Baudrateselection:1200, 2400,4800, 9600and 19200
Page
Page
CHAP
13
TER 3 INSTALLATION
3.1 GENERAL
3.2 PREPARATION FOR USE
14
mount slides assembly
1: Rack
Fig. 3
3.5 LOCATON, MOUNTING AND COOLING
Fig.3-2: Stripped Wires installed in Strain Relief
16
3.8 TURN
(Phoenix)
Plug P/N: MC1,5/5-ST-3,81
Fig.3-4: J2 Sense connector default conn ection
Page
18
3.9 CONNECTING THE LOAD
Page
Page
Page
Page
+L
+
+L
+
24
+L
+
25
OUTPUT TERMINAL GROUNDING
3.10 LOCAL AND REMOTE SENSING
Fig.3-14: J2 Sense connector location
Page
27
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS
Table 4
the power supply front panel.
1 to review the controls, indicators and meters located on
See Fig.4
Page
29
4.3 REAR PANEL CONNECTIONS AND CONTROLS
Fig.4-2: Rear panel connections and controls
30
4.4 REAR PANEL SW1 SETUP SWITCH
Fig.4-3: SW1 setup DIP-switch
4.4.2
aded screwdriver to change the SW1 switch setting.
bl
Off. Then use any small flat
32
4.5 REAR PANEL J1 PROGRAMMING AND MONITORNG CONNECTOR
Page
CHAPTER 5 LOCAL OPERATION
35
5.3
OVER VOLTAGE PROTECTION (OVP)
36
OUTPUT SHUT
5.7
5.6
5.5
37
5.8
2 for
The SO control logic can be selected by the rear panel SW1 Setup switch. Refer to Table 5
solated from the power supply output.
38
START AND AUTO
5.11 SAFE
RESTART MODES
5.12 OVER TEMPERATURE PROTECTON (OTP)
39
5.14 SERIES OPERATION
Page
41
5.15 PARALLEL OPERATION
Page
Page
44
5.17 FRONT
5.16 DAISY
CHAIN CONNECTION
PANEL LOCKING
CHAPTER 6 REMOTE ANALOG PROGRAMMING
6.2 LOCAL/REMOTE AN
6.1 INTRODUCTION
ALOG INDICATION
6.3 LOCAL/REMOTE ANALOG INDICATION
46
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND OUTPUT
CURRENT
47
6.5 RESISITIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT
48
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT
49
CHAPTER 7 RS232 & RS485 REMOTE CONTROL
7.1 INTRODUCTION
7.2 CONFIGURATION
50
7.3 REAR PANEL RS232/RS485 CONNECTOR
Page
52
7.5 CONNECTING
L=2m typ.
L=2mtyp.
Fig.7-3: RS232 cable with DB9 con nector (P/N: GEN/232-9)
53
7.6 COMMUNICATION INTERFACE PROTOCOL
54
7.7 ERROR MESSAGES
7.8 COMMAND SET DESCRIPTION
Page
Page
57
7.9 GLOBAL OUTPUT COMMANDS
58
7.10 SINGLE BYTE COMMANDS
Page
Page
GEN750W model
s
program the power supply over the rated values.
The power supply can accept values higher 5% than the table values, howeverit is not rec ommended to
4: Current programming range
62
7.11 STATUS, ERROR AND SR
Q REGISTERS
Status Registers
Serial
Fig.7-7: Status and Error Registers D iagram
9 for the Status Condition register bits.
tion Register bits and Table 7
i
Cond
7.11.2 Conditional Registers (continued)
7.11.3
r Remote mode.
will be generated either in Local o
The SRQ message is: Inn terminated by CR, where the nn is the power supply address. The SRQ
Page
Page
67
7.12 SERIAL COMMUNICATION TEST SET
UP
68
CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION
8.2 SPECIFICATION
8.1 INTRODUCTION
S
69
8.3 ISOLATED PROGRAMMING & MONITORING CONNECTOR
70
8.4 SETUP AND OPERATING INSTRUCTIONS
71
CHAPTER 9 MAINTENANCE
9.5 PARTS REPLACEMENT AND REPAIR
9.2 UNIT
9.1 INTRODUCTION
S UNDER WARRANTY
72
9.7 FUSE RATING
