Setup and Operating Instructions | TDK 1500W, 750W specs

8.4 SETUP AND OPERATING INSTRUCTIONS

CAUTION

To prevent damage to the unit, do not program the output voltage and current to higher than the power supply rating.

8.4.1Setting up the power supply for 0-5V/0-10V Isolated Programming and Monitoring Perform the following procedure to configure the power supply:

1.Turn the power supply AC power switch to Off.

2.Connect a wire jumper between J1-8 and J1-12 (refer to Table 4-4).

3.Set the Setup switch SW1, positions 1 and 2 to the UP position.

4.Set SW1, position 3 to select the Programming Voltage Range: Down=0-5V, Up=0-10V.

5.Set SW1, position 4 to select the Monitoring Range: Down=0-5V, Up=0-10V.

6.Ensure that SW1, positions 7 and 8 are in the Down position.

7.Connect the programming sources to the mating plug of the Isolated Programming connector. Observe for correct polarity of the voltage source.

NOTE

J1-8 and J1-12 must be shorted together with a wire jumper.

8. Set the programming sources to the desired levels and turn the power supply ON.

8.4.2Setting up the power supply for 4-20mA Isolated Programming and Monitoring Perform the following procedure to configure the power supply:

1.Turn the power supply AC power switch to Off.

2.Connect a wire jumper between J1-8 and J1-12 (refer to Table 4-4).

3.Set the Setup switch SW1, positions 1 and 2 to the Up position.

4.Set SW1, position 3 to the Up position.

5.Set SW1, position 4 to the Up position.

6.Ensure that SW1 positions 1 and 2 to their Up position.

7.Connect the programming source to the mating plug of the Isolated Programming connector. Observe for correct polarity of the voltage source.

NOTE

J1-8 and J1-12 must be shorted together with a wire jumper.

8. Set the programming sources to the desired levels and turn the power supply ON.

NOTE

SW1 position 3 and 4 must be in the Up position for operation with 4-20mA Isolated Programming and Monitoring.

70

83-507-013 Rev. D

Image 78

TDK 1500W, 750W technical manual Setup and Operating Instructions

Contents

Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Disclaimer Limitation of WarrantyWarranty Service Trademark Information Safety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Sicherheits-und Warnsymbole Anderungen and BauteileersatzUmweltbedingungen Introduction Features and optionsGeneral Information General Description Analog voltage programming and monitoring Multiple output power systemControl via the serial communication port Parallel operation Accessories Specifications Chapter Vout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Preparation for USE InstallationGeneral Initial Inspections AC Source Requirements AC Input Power ConnectionLOCATON, Mounting and Cooling Rack Mount Slides optional AC Input Wire Connection, 1500W models AC Input Connector, 1500W modelsAC Input Connector, 750W models AC Input Cord TURN-ON Checkout Procedure GeneralPrior to Operation OVP Check Constant Voltage CheckConstant Current Check UVL Check Connecting the Load Wire termination AWG Noise and Impedance Effects Inductive loadsMaking the load connections 6V to 60V Models Wire terminal lug 2 places 80V to 600V Models Load wires connection to the output connector Connecting single loads, local sensing default Connecting single loads, remote sensingConnecting multiple loads, radial distribution method Multiple load connection with distribution terminals Grounding outputs Local and Remote Sensing Sense wiringOutput Terminal Grounding Local sensing 10.4 J2 sense connector technical information Remote sensing Front and Rear Panel Controls and Connectors Front Panel Controls and Indicators Auxiliary Function Rear Panel Connections and Controls Rear panel connections and controls Rear Panel SW1 Setup Switch Resetting the SW1 switch 1 SW1 position function Rear Panel J1 Programming and Monitorng Connector Making J1 connections Ifcom SignalEnain Local Constant Voltage Mode Constant Current ModeLocal Operation Over Voltage Protection OVP Setting the OVP levelResetting the OVP circuit Automatic Crossover Foldback Protection Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Output ON/OFF Control ENABLE/DISABLE Control VIA Rear Panel J1 Connector CV/CC SignalPsok Signal Auto-restart mode Over Temperature Protecton OTPLast Setting Memory Safe-start mode Series Operation Series connection for increased output voltage Series connection for positive and negative output voltage Series connection for positive/negative output voltages Parallel Operation Master and Slave units default operation Advanced parallel configurationSetting the units as Master or Slave Connection to the load To release units from Slave mode Current display accuracyAST OFF *OUT OFF Unlocked front panel DAISY-CHAIN ConnectionFront Panel Locking Locked front panel Remote Analog Programming LOCAL/REMOTE Analog Indication Down Remote voltage programming connection Resisitive Programming of Output Voltage and Current Limit Remote resistive programming Remote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control Configuration Rear Panel RS232/RS485 Connector 6 RS232/RS485 port in Local modeFront panel in Remote mode MD Mode SRQ MD Mode Option Factory Installed MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ Retransmission Connecting Power Supplies to RS232 or RS485 BUS Single power supply Communication Interface Protocol Error Messages Command SET Description Initialization Control Commands ID Control CommandsOutput Control Commands FILTER? DVC?Filter OUT? Global Output Commands Disable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Enable SRQ retransmission MD Mode Option Required Test if MD Mode is Installed Addressed commands with response Read registersPrint Power On Time Addressed commands without response Acknowledge SRQ 1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range STATUS, Error and SRQ Registers 10.6 Status Control Commands Conditional Registers Status Registers Service Request Enable and Event Registers BIT Fault Enable Register Fault Event Register Status Enable Register Status Event Register Power supply set-up Serial Communication Test SET-UPCommunication Test 1 0-5V/0-10V Option PN IS510 SpecificationsIsolated Analog Programming Option PPM/C Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP