Isolated Programming & Monitoring Connector | TDK 750W, 1500W

8.3 ISOLATED PROGRAMMING & MONITORING CONNECTOR

Refer to Table 8-1 for detailed description of the rear panel Isolated Programming & Monitoring connector. To provide the lowest noise performance, it is recommended to use shielded-twisted pair wiring.

Refer to Fig.8-1 for description of the Isolated Analog Programming & Monitoring connector. Isolated programming plug P/N: MC1.5/8-ST-3.81, Phoenix.

1

2

3

4

5

6

7

8

Shield

+VPROG_ISO

+IPROG_ISO GND_ISO

Shield

+IMON_ISO

+VMON_ISO GND_ISO

Fig.8-1: Isolated Programming & Monitoring connector

Table 8-1: Detailed description of Isolated programming & Monitoring connector

				Range 0-5/0-	Range 4-20mA
	Terminal	Signal name	Function	10V	Range 4-20mA
	Terminal	Signal name	Function	10V	IS420 option
				IS510 option	IS420 option
				IS510 option
	1	SHLD	Shield, connected internally to	Chassis ground
	1	SHLD	chassis of the power supply.	Chassis ground
			chassis of the power supply.
	2	+VPROG_ISO	Output Voltage programming in-	0-5V/0-10V	4-20mA
	2	+VPROG_ISO	put	0-5V/0-10V	4-20mA
			put
	3	+IPROG_ISO	Output Current programming in-	0-5V/0-10V	4-20mA
	3	+IPROG_ISO	put	0-5V/0-10V	4-20mA
			put
	4	GND	Ground for programming signals.	Ground	Ground

	5	GND	Ground for programming signals.	Ground	Ground

	6	+VMON_ISO	Output voltage monitoring output	0-5V/0-10V	4-20mA

	7	+IMON_ISO	Output current monitoring output	0-5V/0-10V	4-20mA

	8	SHLD	Shield, connected internally to	Chassis ground
	8	SHLD	chassis of the supply.	Chassis ground
			chassis of the supply.

CAUTION

When the Isolated Analog Option is installed, do not apply any signals to the non-isolated VPGM and IPGM (J1-9 and J1-10) pins. All other J1 features may be used normally. Refer to Section 4.5 for a description of J1 features.

69

83-507-013 Rev. D

Image 77

TDK 750W, 1500W technical manual Isolated Programming & Monitoring Connector

Contents

Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Warranty Service Limitation of WarrantyDisclaimer Trademark Information Safety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Umweltbedingungen Sicherheits-und WarnsymboleAnderungen and Bauteileersatz General Information Features and optionsIntroduction General Description Control via the serial communication port Multiple output power systemAnalog voltage programming and monitoring Parallel operation Accessories Chapter Specifications Vout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings General InstallationPreparation for USE Initial Inspections LOCATON, Mounting and Cooling AC Input Power ConnectionAC Source Requirements Rack Mount Slides optional AC Input Connector, 750W models AC Input Connector, 1500W modelsAC Input Wire Connection, 1500W models AC Input Cord Prior to Operation TURN-ON Checkout ProcedureGeneral Constant Current Check Constant Voltage CheckOVP Check UVL Check Connecting the Load AWG Wire termination Making the load connections 6V to 60V Models Noise and Impedance EffectsInductive loads 80V to 600V Models Wire terminal lug 2 places Load wires connection to the output connector Connecting multiple loads, radial distribution method Connecting single loads, local sensing defaultConnecting single loads, remote sensing Grounding outputs Multiple load connection with distribution terminals Output Terminal Grounding Sense wiringLocal and Remote Sensing Local sensing Remote sensing 10.4 J2 sense connector technical information Front Panel Controls and Indicators Front and Rear Panel Controls and Connectors Auxiliary Function Rear panel connections and controls Rear Panel Connections and Controls Rear Panel SW1 Setup Switch 1 SW1 position function Resetting the SW1 switch Making J1 connections Rear Panel J1 Programming and Monitorng Connector Enain SignalIfcom Local Local Operation Constant Voltage ModeConstant Current Mode Resetting the OVP circuit Setting the OVP levelOver Voltage Protection OVP Automatic Crossover Under Voltage Limit UVL Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorFoldback Protection Output ON/OFF Control Psok Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorCV/CC Signal Last Setting Memory Over Temperature Protecton OTPAuto-restart mode Safe-start mode Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Parallel Operation Setting the units as Master or Slave Advanced parallel configurationMaster and Slave units default operation Connection to the load AST OFF *OUT OFF To release units from Slave modeCurrent display accuracy Front Panel Locking DAISY-CHAIN ConnectionUnlocked front panel Locked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control Front panel in Remote mode Rear Panel RS232/RS485 Connector6 RS232/RS485 port in Local mode MD Mode enable Serial communication mode MD Mode Option Factory Installed MD Mode DescriptionMD Mode SRQ MD Mode SRQ Retransmission Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages Output Control Commands Initialization Control CommandsID Control Commands Filter DVC?FILTER? OUT? Global Output Commands Enable MD Mode MD Mode Option Required Single Byte CommandsDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option Required Print Power On Time Addressed commands with response Read registersTest if MD Mode is Installed Addressed commands without response Acknowledge SRQ 1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range 10.6 Status Control Commands STATUS, Error and SRQ Registers Status Registers Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Communication Test Power supply set-upSerial Communication Test SET-UP Isolated Analog Programming Option Specifications1 0-5V/0-10V Option PN IS510 PPM/C Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating