Genesystm 750W/1500W | TDK instruction

TECHNICAL MANUAL FOR

GENESYSTM 750W/1500W

Programmable DC Power Supplies

Document: 83-507-013 Rev D

TDK-Lambda Americas Inc.

405 Essex Road, Neptune, NJ 07753

Tel: (732) 922-9300

Fax: (732) 922-9334

Web: www.US.TDK-Lambda.com/HP

Image 1

TDK technical manual Genesystm 750W/1500W

Contents

Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Warranty Service Limitation of WarrantyDisclaimer Trademark Information Safety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Anderungen and Bauteileersatz Sicherheits-und WarnsymboleUmweltbedingungen General Information Features and optionsIntroduction General Description Control via the serial communication port Multiple output power systemAnalog voltage programming and monitoring Parallel operation Accessories Chapter Specifications Vout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings General InstallationPreparation for USE Initial Inspections LOCATON, Mounting and Cooling AC Input Power ConnectionAC Source Requirements Rack Mount Slides optional AC Input Connector, 750W models AC Input Connector, 1500W modelsAC Input Wire Connection, 1500W models AC Input Cord General TURN-ON Checkout ProcedurePrior to Operation Constant Current Check Constant Voltage CheckOVP Check UVL Check Connecting the Load AWG Wire termination Inductive loads Noise and Impedance EffectsMaking the load connections 6V to 60V Models 80V to 600V Models Wire terminal lug 2 places Load wires connection to the output connector Connecting single loads, remote sensing Connecting single loads, local sensing defaultConnecting multiple loads, radial distribution method Grounding outputs Multiple load connection with distribution terminals Output Terminal Grounding Sense wiringLocal and Remote Sensing Local sensing Remote sensing 10.4 J2 sense connector technical information Front Panel Controls and Indicators Front and Rear Panel Controls and Connectors Auxiliary Function Rear panel connections and controls Rear Panel Connections and Controls Rear Panel SW1 Setup Switch 1 SW1 position function Resetting the SW1 switch Making J1 connections Rear Panel J1 Programming and Monitorng Connector Enain SignalIfcom Local Constant Current Mode Constant Voltage ModeLocal Operation Resetting the OVP circuit Setting the OVP levelOver Voltage Protection OVP Automatic Crossover Under Voltage Limit UVL Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorFoldback Protection Output ON/OFF Control CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorPsok Signal Last Setting Memory Over Temperature Protecton OTPAuto-restart mode Safe-start mode Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Parallel Operation Setting the units as Master or Slave Advanced parallel configurationMaster and Slave units default operation Connection to the load Current display accuracy To release units from Slave modeAST OFF *OUT OFF Front Panel Locking DAISY-CHAIN ConnectionUnlocked front panel Locked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control 6 RS232/RS485 port in Local mode Rear Panel RS232/RS485 ConnectorFront panel in Remote mode MD Mode enable Serial communication mode MD Mode Option Factory Installed MD Mode DescriptionMD Mode SRQ MD Mode SRQ Retransmission Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages ID Control Commands Initialization Control CommandsOutput Control Commands Filter DVC?FILTER? OUT? Global Output Commands Enable MD Mode MD Mode Option Required Single Byte CommandsDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option Required Print Power On Time Addressed commands with response Read registersTest if MD Mode is Installed Addressed commands without response Acknowledge SRQ 1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range 10.6 Status Control Commands STATUS, Error and SRQ Registers Status Registers Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Serial Communication Test SET-UP Power supply set-upCommunication Test Isolated Analog Programming Option Specifications1 0-5V/0-10V Option PN IS510 PPM/C Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating