Manuals / Jonsered / Lawn and Garden / Chainsaw

Jonsered CS 2141 Fuelling, Chain oil, Min 3 m, 10ft, Always shut off the engine before refuelling

Models: CS 2145 CS 2150 CS 2141

1 36

Download 36 pages 50.37 Kb

Page 27

Chain oil

FUEL HANDLING

Chain oil

•	The chain lubrication
	system is automatic. Always
	use special chain oil with
	good adhesive
	characteristics.
•	In countries where no
	special chain oil is available,
	EP 90 transmission oil can
	be used.
•	Never use waste oil. This
	results in damage to the oil
	pump, the bar and the
	chain.

Fuelling

!Taking the following precautions, will lessen the risk of fire.

•Do not smoke or place warm objects in the vicinity of the fuel.

•Always shut off the engine before refuelling.

•Slowly open the fuel cap, when filling fuel, so that possible overpressure is slowly released.

•Tighten the fuel cap carefully after fuelling.

•Always move the saw from the fuelling area before starting.

•	It is important to use oil of
	the right viscosity according
	to the air temperature.
•	In temperatures below 0oC
	(32oF) some oils become
	too viscous. This can
	overload the oil pump and
	result in damage to the oil
	pump components.
•	Contact your servicing
	dealer when choosing chain
	oil.

Clean around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter should be changed at least once a year. Contamination in the fuel tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before fuelling. The volume of chain oil and fuel tanks are adjusted to each other. Therefore, always fill chain oil and fuel at the same time.

Min 3 m

(10ft)

English – 27

Image 27

Jonsered CS 2141 manual Fuelling, Chain oil, Min 3 m, 10ft, Taking the following precautions, will lessen the risk of fire

Contents

EPA EPA EPA Operator´s manual Symbols KEY TO SYMBOLSSafety instructions CONTENTSContents Before using a new sawSAFETY INSTRUCTIONS CHAIN SAW SAFETY EQUIPMENTPERSONAL PROTECTIVE EQUIPMENT 1 Chain brake and front hand guard 3a StartingSAFETY INSTRUCTIONS SAFETY INSTRUCTIONS 2 Throttle lock3 Chain catcher 4 Right hand guardSAFETY INSTRUCTIONS 6 Stop switch5 Vibration damping system 7 Muffler2 Checking the front hand guard Inspecting, maintaining and servicing chain saw safety equipmentWhen the bar hits the stump the brake should be applied 1 Checking brake band wear3 Chain catcher SAFETY INSTRUCTIONS6 Stop switch 2 Throttle lockReduce the risk of the chain breaking or jumping CUTTING EQUIPMENTThe 5 basic rules Reduce the risk of kickbackB Saw chain See the ”Technical data”1 Cutting equipment designed to minimise kickback A BarB Sharpening cutting teeth 2 Sharpening your chain and adjusting raker clearanceThe following faults will increase the risk of kickback considerably A General information on sharpening cutting teethThe risk of kickback is increased if the raker clearance is too large C General advice on setting raker clearanceD Setting the raker clearance 3 Tensioning the chainNever use waste oil 4 Lubricating cutting equipmentA Chain oil B Filling with chain oilF Checking wear on cutting equipment E Needle bearing maintenanceshould contact your service agent C Checking chain lubricationH Bar HOW TO AVOID KICKBACKWhat is kickback? MOST CHAIN SAW ACCIDENTS HAPPEN WHEN THE CHAIN TOUCHES THE OPERA- TORSAFETY INSTRUCTIONS General rulesDo not let go of the handles Never use the saw one- handedSAFETY INSTRUCTIONS GENERAL SAFETY PRECAUTIONSMin. 3 m 10 ftSAFETY INSTRUCTIONS 1 Basic safety rulesGENERAL WORKING INSTRUCTIONS DO NOT ATTEMPT ANY TASK THAT YOU FEEL UNSURE OFTerms Always use full throttle when cutting2 Basic cutting technique GeneralB Felling direction 3 Tree felling techniqueA Safe distance LimbingFELLING CUT C Clearing the trunk and preparing your retreatD Felling DIRECTIONAL CUTF Cutting the trunk into logs General advice4 Freeing a tree that has fallen badly = high accident risk E LimbingWhat is what? WHAT IS WHAT?Mounting guide bar and chain ASSEMBLYGasoline Always provide for good ventilation when handling fuelFUEL HANDLING FuelmixMin 3 m Taking the following precautions, will lessen the risk of fireFuelling Chain oilStop START AND STOPStart and stop StartFine adjustment MAINTENANCEFunctioning, Basic setting, Final setting Basic setting and running inTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordMuffler Needle bearing maintenancepower, difficult to start or Air filterRecommended settings Adjustment of the oil pumpCentrifugal cleaning WARNING! The engine must not be running when making adjustmentsLong-term storage Weekly maintenanceDaily maintenance Monthly maintenance34´z*xv¶5¨ TECHNICAL DATARecommended original and replacement WeightWARRANTY COMMENCEMENT DATE EMISSION CONTROL WARRANTY STATEMENTMANUFACTURER’S WARRANTY COVERAGE OWNER’S WARRANTY RESPONSIBILITIES´z*xv¶5¨ 1082002W49