Jonsered CS 2150 34´z*xv¶5¨, Technical Data, Recommended original and replacement, Engine, Weight

TECHNICAL DATA

	CS 2141	CS 2145	CS 2150
Engine
Cylinder volume, cu.in/cm3	2,49/40,8	2,75/45,0	3,15/51,7
Cylinder bore, inch/mm	1,57/40	1,65/42	1,77/45
Stroke, inch/mm	1,28/32	1,28/32	1,28/32
Idle speed, rpm	2 700	2 700	2 700
Power, kW/ rpm	2,0/ 9 000	2,2/ 9 000	2,3/ 9 000
Ignition system
Manufacture	SEM	SEM	SEM
Type of ignition system	CD	CD	CD
Spark plug	NGK BPMR 7A	NGK BPMR 7A	NGK BPMR 7A
Electrode gap, inch/mm	Champion RCJ7Y	Champion RCJ7Y	Champion RCJ7Y
	0,020/0,5	0,020/0,5	0,020/0,5
Fuel and lubrication system
Manufacturer	Zama	Zama	Zama
Carburetor type	C3-EL18	C3-EL18	C3-EL18
Fuel capacity, US pint/litre	1,05/0,50	1,05/0,50	1,05/0,50
Oil pump capacity at 9000 rpm, ml/min	9	9	5-12
Oil capacity, US pint/litre	0,59/0,28	0,59/0,28	0,59/0,28
Type of oil pump	Automatic	Automatic	Automatic
Weight
Without bar and chain, Lbs/kg	10,8/4,9	10,8/4,9	10,8/4,9
Chain/bar
Standard bar length, inches/cm	13"/33	13"/33	13"/33
Recommended bar lengths, inches/cm	13-18"/33-45	13-18"/33-45	13-18"/33-45
Usable cutting length, inches/cm	12-17"/31-43	12-17"/31-43	12-17"/31-43
Chain speed at max. power, m/sec	17,3	17,3	17,3
Pitch, inch/mm	0,325"/8,25	0,325"/8,25	0,325"/8,25
Thickness of drive link, inch/mm	0,050"/1,3	0,050"/1,3	0,050"/1,3
	0,058"/1,5	0,058"/1,5	0,058"/1,5
Number of teeth on drive sprocket	0,063"/1,6	0,063"/1,6	0,063"/1,6
	7	7	7

Recommended original and replacement	Guide bar			Saw chain
bar and chain combinations	Length	Pitch	Max nose
Following is a list of recommended cutting equipment for the Jonsered
	inch	inch	radius
chain saw model CS 2141, CS 2145, CS 2150. The combinations of
	13	0,325"	10T	Jonsered S30 or Oregon 95VP
powerhead, bar and chain have been investigated in accordance with
	15	0,325"	10T
the kickback and vibration requirements of ANSI B 175.1 – 2000.
	16	0,325"	10T
The guide bar nose radius is determined by either the maximum
	18	0,325"	10T
number of teeth in the nose sprocket or the corresponding maximum
nose radius of a solid bar.	13	0,325"	10T	Jonsered S25 or Oregon 21BP
	15	0,325"	10T
The following list is the chain saw manufacturers recommendations.	16	0,325"	10T
There may be other combinations available, which will also achieve	18	0,325"	10T
kickback reduction.
	13	0,325"	10T	Total/Sabre 528PS
As we are listing the maximum guide bar nose radius, you may use a	15	0,325"	10T
	16	0,325"	10T
guide bar with smaller nose radius than in our list. For guide bars of the
	18	0,325"	10T
same length, all sprocket-nose guide bars of the same pitch and
	15	0,325"	10T	Total 528NK, Total 528NKD
having the same number of of sprocket teeth may be considered to
have equivalent kickback energy. A hard nose bar having the same	16	0,325"	10T	Sabre 528P (Single or Dual Raker)
length and nose radius as a sprocket-nose bar may be considered to	18	0,325"	10T
have equivalent or less kickback energy than the sprocket-nose bar.	Note: For the chains above you are free to choose between 0,050",
Low kickback saw chain is a chain which has only met the kickback	0,058" and 0,063" gauge drive link for the corresponding bar, see
	table below.
performance requirements of ANSI B 175.1 safety requirements for
gasoline-powered chain saws when tested on the representative	0,050" (1,3 mm)		S30 / 95VP	20BP	520PS
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We
	0,058" (1,5 mm)		–	S25 / 21BP	528PS
recommend that you as replacement use the listed chains or "Low
kickback saw chains" which are available at your dealer.	0,063" (1,6 mm)		–	22BP	523PS

34´®z*xv)¶5]¨

– English