JVC BR-DV600EA, BR-DV600UA manual Preparation

5 PREPARATION

Preparing this unit for recording or playback.

CH-1/3				OPERATE
				ON/OFF
		VIDEO CASSETTE RECORDER BR-DV600UA		[OPERATE] button
REC LEVEL				EJECT
MENU	ADVANCE	PRESET		[EJECT] button
CH-2/4		REC	PLAY	PAUSE
	SHIFT	SHIFT		REMOTE
HOLD	SHIFT	A.

5 PREPARATION
Built-in clock setting
Time data is recorded in the sub code area of the tape during recording. In the Play mode, this data is read out and can be
shown on the on-screen display or the counter display.
[Reference]
Clock data is retained for about 60 hours after the
6-hour power supply is used up (Operate On mode).	ADVANCE: Changes the value.
	PRESET: Enters the set value.
MENU ADVANCE PRESET

	SELECT		SET				REW STOP	LOCAL
	V.IN/A.MONI		A.OUT COUNTER		MENU			FF
PHONES						S	F	MIC
	DV	L	CH-1/2	CTL
	LINE	MIX	MIX	TC
	Y/C	R	CH-3/4	UB
	(CPN)

HOLD: Start SHIFT: Digit shift

		SHIFT	SHIFT
HOLD		SHIFT	A. DUB
SELECT		SET
V.IN/A.MONI		A.OUT	COUNTER
DV	L	CH-1/2		CTL
LINE	MIX	MIX		TC
Y/C	R	CH-3/4		UB
(CPN)

CH 1/3		OVER	AUTO OFF DEW
40 30 20 10	0	dB
CH 2/4		OVER SERVO RF

32k	48k	SLAVESLAVE	PB		NDF	HOLD
AUD LOCK	SPSP
MENU		H		M	S		F

[AUDIO MONITOR] switch

TC: Time

UB: Date

Time and date display

Turn the power ON.

Press the [OPERATE] switch. The counter display lights up.

Turn the power OFF

Press the [OPERATE] switch. “oPE-oFF” is shown in the counter display.

Loading/unloading a cassette

Insert the cassette into the cassette loading slot with the window facing up. Push the cassette in slowly until the loading mechanism starts automatic loading.

[The VCR enters the Stop mode and the cassette

indicator ( ) lights.

Press the [EJECT] button to eject the cassette.

[The cassette tape is ejected.

Audio monitor selection

Set the No. 054 <AUDIO MONITOR> menu switch to “AUDIO”. Use the [AUDIO MONITOR] switch to select the audio channel to monitor (via the [AUDIO MONITOR OUT] connectors).  See “Playback preparation” on page 28.

				5 Setting procedure
				The names of the operation buttons are shown above the
				buttons.
				1 Set the tape counter display to the time display.
H	M	S	F	Set the No. 516 <DISPLAY SELECT> menu switch to
				“CLOCK”.
				 See No. 516 <DISPLAY SELECT> on page 23.
H	M	S	F	2 Set the [COUNTER] switch to “TC” or “UB”.
				• To set the time, set to “TC”.
				The time display is shown in the tape counter.
				• To set the date, set to “UB”.
				The date display is shown in the tape counter.
H	M	S	F	3 Engage the setting mode.
				Press the [HOLD] button.
				• Clock setting
				[ The hour digit starts to blink.
H	M	S	F	• Date setting
				[ The month digit starts to blink. (U MODEL)
				[ The day digit starts to blink. (E MODEL)
				4 Change the value.
H	M	S	F	Each time the [ADVANCE] button is pressed, the value
				of the blinking digit increases.
				While holding down the [SHIFT] button, press the
				[ADVANCE] button to reset the value as follows.

•Clock setting: “00:00:00”

•Date setting: “01:01:2000”

5 Shift the digit. Press the [SHIFT] button.

•Clock setting: Each time the [SHIFT] button is pressed, the blinking cursor moves in the order of hours [ minutes [ seconds.

•Date setting: Each time the [SHIFT] button is pressed, the blinking cursor moves in the order of month [ day

[ year. (U MODEL), day [ month [year. (E MODEL). Repeat steps 4 to 5 to change the values for each digit.

6 Enter the set data. Press the [PRESET] button to enter the set data.

24 25