JVC DR-MV1S 42 EN OPERATIONS ON DVD DECK, DVD, ENTER, ENTER, NOTE:, ENTER, NOTES:, VCR/DVD, DVD TIMER, DVD TIMER, number key “7”, TV/CABLE/DBS/DVD, 3 Press PROG/CHECK to

42 EN OPERATIONS ON DVD DECK

Manual Timer Programing				10 Press ENTER to access the Program Confirmation screen.
				11 Press ENTER to complete timer programing.
				● To program another timer, repeat steps 3 – 11.
				12 Press DVD TIMER (#) to engage the unit’s timer mode. The
				DVD timer lamp lights up on the unit and the VCR deck is
You can program this unit to timer-record as many as 8 programs.				automatically selected. When the VCR deck is in timer standby
				mode, the unit is automatically turned off.
If you do not know the PlusCode number for the program you wish				#
to record, use the following procedure to set your unit to				● To disengage the timer mode, press DVD TIMER ( ) again.
				NOTES:
timer-record the program.
				● When two successive programs are recorded on a DVD-RW disc with
● Make sure that the unit’s built-in clock is set properly.				Manual Timer Programing function, the beginning of the second one
				may be left off the recording.
● Turn on the unit.
				● If the copy limited program is received during timer-recording, the unit
● Turn on the TV and select the video channel (or AV mode).
				enters Record Pause mode. Recording starts again if it is switched to
● Slide the TV/CABLE/DBS/DVD switch to DVD.
				a recordable broadcast during the time you programed.
				Cable Box and DBS Receiver Users
DVD TIMER (#)				To timer-record a satellite broadcast using Manual Timer
VCR/DVD				Programing:
	1	2	3	A Perform “Cable Box and/or DBS Receiver Control Setting
	4	5	6
				(DVD Deck Only)” ( pg. 22).
7	7	8	9
				B Perform “Manual Timer Programing” ( pg. 42).
PROG/CHECK		0
				C Leave the cable box or DBS receiver’s power on.
ENTER			rtw e
				ATTENTION FOR DBS RECEIVER USERS
				If you are using a DBS receiver (unless “DBS RECEIVER SET”
				is set to “OFF”  pg. 22), the band indication (TV, CATV or
				DBS) appears on the left of the channel number indication.
				No indication: To timer-record a regular TV broadcast received
				on the unit.
				CATV: To timer-record a cable TV broadcast received on the unit,
				or through a cable box (unless “CABLE BOX SET” is set to
				“OFF”  pg. 22).
1 Load a recordable disc.				DBS: To timer-record a satellite broadcast received through a
				DBS receiver.
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on				NOTE:
the unit.				If the channel number entered requires that the band be set,
3 Press PROG/CHECK to				“7=DBS” is displayed on the screen.
				If this happens, press the number key “7” to select “DBS”.
access the Program Check
screen.

●When “PROGRAM FULL DELETE

UNWANTED TIMER PROGRAM” appears on the TV screen, you need to cancel some of the reserved programs. ( pg. 45)

4 Press rt to select “NEW TIMER PROGRAM”, then press ENTER. The program screen appears.

5 Press rt to set the desired date.

● The current date appears on the TV screen. The date you enter appears in its place.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt advances/goes back the start time in 1-min. increments.

●To advance/go back the start time in 30-min. increments, press and hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

8 Press w e to select “CH”, then press rt to select the desired channel.

●If you are using a DBS receiver, see “ATTENTION FOR DBS RECEIVER USERS” in the right column.

9 Set the other recording options as required.

●Refer to step 6 in “VCR Plus+® Timer Programing” ( pg. 41).