JVC ENLYT1127-001A Initialising a Memory Card, Making a New Folder, To Reset The No. Of Prints

5 Select the number of prints by pressing + or – 5 and press SELECT/SET 3.

Repeat steps 3 through 5 for the desired number of prints.

¥The number of prints can be set up to 15.

¥To correct the number of prints, select the image again and change the number.

6 Press + or – 5 to select ÒRETURNÓ and press SELECT/SET 3. Selection is complete. ÒSAVE?Ó appears.

¥If you did not change any settings in step 3 through 5, the Menu Screen reappears.

7 Press + or – 5 to select ÒEXECUTEÓ, then press SELECT/SET 3 to save the setting you have just made.

¥To cancel selection, press + or – 5 to select ÒCANCELÓ and press SELECT/SET 3.

To Reset The No. Of Prints . . .

..... select ÒRESETÓ in step 4 of ÒTO PRINT ALL STILL

IMAGES (ONE PRINT FOR EACH)Ó on pg. 23. The number of prints is reset to 0 for all still images.

CAUTION

While performing the above, never disconnect power, as this may cause the memory to be corrupted. For safety, all buttons including the Power Switch @ are disabled in step 6.

NOTES:

●ÒBATTERY LOWÓ appears if the battery remaining power is too low.

●If you load a memory card already set as shown above in a printer compatible with DPOF, it will make prints of the selected still images automatically.

●To print images recorded on a tape, first dub them to a memory card ( pg. 23).

3 Press + or – 5 to select ÒEXECUTEÓ, then press SELECT/SET 3. The new folder (such as Ò101JVCGRÓ) will be made and the file name of the next shot starts from DVC00001.

Folder and File names

Each time shooting takes place, a file name is made using a number which is larger by one than the largest number of the file names which are in use. Even if you delete an image or video clip file with a number in the middle of range, the number will not be used for a new shot; a gap will remain in the numerical sequence. If the file name reaches DVC09999, a new folder (such as Ò101JVCGRÓ) will be made and the file name will start again from DVC00001.

Initialising A Memory Card

You can initialise a memory card anytime.

After initialising, all files and data stored on the memory card, including those which have been protected, are cleared.

1 Perform steps 1 through 3 of ÒNormal PlaybackÓ ( pg. 18).

2 Press MENU 4. The Menu Screen appears. Press + or – 5 to select ÒFORMATÓ and press SELECT/SET 3. The FORMAT Screen appears.

3 Press + or – 5 to select ÒEXECUTEÓ and press SELECT/SET 3. The memory card is initialised. When initialisation is finished, ÒNO IMAGES STOREDÓ or ÒNO E-MAIL CLIP STOREDÓ appears.

¥To cancel initialisation, press + or – 5 to select ÒRETURNÓ and press SELECT/SET 3.

Making A New Folder

New files you are going to store can be separated from previously stored files by resetting the file name to DVC00001; these new files will be stored in a new folder.

1 Perform steps 1 through 3 of ÒNormal PlaybackÓ ( pg. 18).

2 Press MENU 4. The Menu Screen appears. Press + or – 5 to select ÒNO. RESETÓ, then press SELECT/ SET 3. The NO. RESET Screen appears.

CAUTION

Do not perform any other operation (such as turning off the camcorder) during initialisation. Also, be sure to use the provided AC Adapter, as the memory card may be corrupted if the battery becomes exhausted during initialisation. If the memory card becomes corrupted initialise it.

EN

24 ADVANCED FEATURES