JVC ENLYT1127-001A manual Audio Dubbing, Insert Editing, To hear the dubbed sound during playback

Audio Dubbing

The audio track can be customized only when recorded in the 12-bit mode (
pg. 32).

NOTES:

●Audio Dubbing is not possible on a tape recorded in

16-bit audio, on a tape recorded in the LP mode or on a blank portion of a tape.

●To perform Audio Dubbing while watching on the television, make connections (
pg. 16).

1 Play back the tape to locate the point where editing will start, then press PAUSE (6) H.

2 While holding A.DUB (e) S on the remote control, press PAUSE (6) H. “6e” O and “MIC” appear.

3 Press PLAY (4) D, then begin “narrating”. Speak into the microphone.

• To pause dubbing, press PAUSE (6) H.

4 To end Audio Dubbing, press PAUSE (6) H, then STOP (5) G.

To hear the dubbed sound during playback . . .

..... set “12bit MODE” to “SOUND 2” or “MIX” in the

Menu Screen (
pg. 36).

NOTES:

●Sound is not heard from the speaker during Audio Dubbing.

●When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately.

●If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas.

●If feedback or howling occurs during TV playback, move the camcorder’s microphone away from the TV, or turn down the TV’s volume.

●If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began.

●During Audio Dubbing, when the tape moves to scenes

recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops (
pg. 56).

●To perform Audio Dubbing with a video unit connected to the camcorder’s S/AV connector &, first set “S/AV

INPUT” to “A/V IN” or “S IN” in the Menu Screen (
pg. 35). “AUX” appears instead of “MIC”.

Stereo microphone

Insert Editing

You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.

NOTES:

●Before performing the following steps, make sure that

“TIME CODE” is set to “ON” in the Menu Screen (
pg. 35, 36).

●Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape.

●To perform Insert Editing while watching in the television, make connections (
pg. 16).

1 Play back the tape, locate the Edit-Out point and press PAUSE (6) H. Confirm the time code at this point (
pg. 35, 36).

2 Press REW (2) a until the Edit-In point is located, then press PAUSE (6) H.

3 Press and hold INSERT (w) A on the remote control, then press PAUSE (6) H. “6w” 0 and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode.

4 Press START/STOP k to begin editing.

•Confirm the insert at the time code you checked in step 1.

•To pause editing, press START/STOP k. Press it again to resume editing.

5 To end Insert Editing, press START/STOP k, then STOP (5) 7.

NOTES:

●Programme AE with special effects (
pg. 27) can be used to spice up the scenes being edited during Insert Editing.

●During Insert Editing, the date and time information changes.

●If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

●During Insert Editing, when the tape moves to scenes

recorded in the LP mode or a blank portion, Insert Editing stops (
pg. 56).

●If a memory card is loaded and “NAVIGATION” is set to

“ON”, a NAVIGATION thumbnail image is stored in the memory card (
pg. 21).

R j

T Y Ul k

I O P S A ;

a s d G F D

f g h K J H

EN

40 USING THE REMOTE CONTROL UNIT