JVC FS-V100 Using the Cassette Deck Recording, Standard Recording, connected auxiliary equipment

Models: FS-V100

1 28
Download 28 pages 54.72 Kb
Page 18
Image 18
Using the Cassette Deck (Recording)
Adhesive tape
Type II detection slot

Using the Cassette Deck (Recording)

TAPE @ #

POWER

FMAUTO

SLEEP DISPLAY MODE PRESET

AUX

TAPE

CD

 

FM/AM

CD

 

 

REPEAT

 

UP

PROGRAM

 

SET

RANDOM

 

DOWN

AHB

 

 

PRO

BASS

TREBLE CANCEL

VOLUME

REMOTE CONTROL RM-SFSV10J

 

 

STANDBY

 

 

 

 

 

 

 

 

 

AHB

 

 

 

AUX

 

 

PRO

 

 

 

POWER

 

 

VOLUME

 

 

 

REC

 

 

TIMER

 

 

REC

REV

 

 

 

 

 

MODE

 

 

CLOCK

 

CD #´8

REV. MODE

 

 

 

CD

 

 

TAPE

FM/AM

CD

OPEN/CLOSE

 

7

TAPE @ #

CD #´8

DOWN

MULTI CONTROL

UP

 

 

PHONES

 

 

 

 

 

7

 

 

 

 

Tape Direction indicator

 

 

 

 

 

 

 

 

 

 

 

REC indicator

REC

When the System is in use, the display shows other items as well.

For simplicity, only the items described in this section are shown here.

Reverse Mode indicator

Recording onto a tape from any of the sound sources is simple. Just place a tape in the Cassette Deck, have the source ready, make one or two settings, and you’re ready to record. For each source the procedure is a little bit different so we explain each separately. But first, here are a few things to make your recordings better.

CAUTION:

If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System.

Things to know before you start recording –––––––––––––––––––––––––––––

It should be noted that it may be unlawful to re- record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic embodied therein.

When you want to record onto both sides of a tape, you can set Reverse mode to do so. Recording automatically stops after recording in the 2direction. Therefore, make sure that the tape direction is 3 when recording with Reverse mode on.

The recording level, which is the volume at which the new tape is being made, is automatically set correctly, so it is not affected by the VOLUME control on the System. Nor is it affected by adjusting the sound effects. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.

Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording.

To record on a cassette with the tabs removed, you must cover the holes with adhesive tape first. However, when a type II tape is used, only cover part of the hole as shown, since the other part of the hole (Type II detection slot) is used to detect the tape type.

Type I and Type II tapes can be used for recording.

Note: At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind on the leader tape first to ensure that the recording will be made without any music part lost.

Standard Recording

You can record any sound source to tape as follows:

1Insert a blank or erasable tape into the Cassette Deck.

2If you want to record on both sides of a tape, press the REV. MODE button on the Unit until the Standard Recording indicator is lit.

When using Reverse mode, insert the tape so that it will be recorded in the forward 3direction.

3Check the recording direction for the tape.

Make sure that the Tape Direction indicator is the same as that for the tape in the Cassette Deck. If the directions are different, press the TAPE @#button to correct the tape direction and then press the 7button to stop the tape.

4Prepare the source by, for example, tuning in a radio station or turning on

connected auxiliary equipment.

Note: For CD recording, refer to “CD Direct Recording” on page 15.

5Press the REC button on the Unit.

The REC indicator lights up and the System begins recording.

Notes for using Reverse mode for recording

When recording in Reverse mode, the System automatically stops when it reaches the end of the reverse 2direction. To record on both sides of a tape, make sure that the recording direction for the tape inserted is forwards 3, and that the Tape Direction indicator is also forwards 3, before you start recording.

To stop at any time during the recording process

Press the 7 button.

14

EN10-22.FS-V100[J]f

14

12/12/00, 10:33 AM

Page 18
Image 18
JVC FS-V100 manual Using the Cassette Deck Recording, Standard Recording, 3Check the recording direction for the tape