JVC G2000 manual Connecting to Various Devices, Signals that Can Be Input to the Projector

Connecting to Various Devices

*Before connection, be sure to turn off the projector and connected devices.

*Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:

■Video signals

(1) Response to color systems

Color system	NTSC	NTSC4.43	PAL	SECAM
Input terminal
VIDEO	à	à	à	à
Y/C	à	à*1	à	- - - - -
Y, PB/B-Y, PR/R-Y	à*2	à*2	à*2	à*2
G, B, R, H/CS, V	à*2	à*2	à*2	à*2

*1 : Responds if Y/C output is available.

*2 : Signifies that component signals (“Y, PB, PR ” / “ Y, B-Y, R-Y” / “G, B, R, H/CS, V”) conform to the signal timing (synchroniza- tion and video period) of each color system. The color systems are used for convenience only.

(2) Response to double density (*1), high-vision signals

Input terminal	NTSC*2	PAL*3	High-vision signal
Y, PB/B-Y, PR/R-Y	à	à	à
G, B, R, H/CS, V	à	à	à

*1 : Signals whose density of scanning lines/field is twice as high.

*2 : Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded 525P progressive sig- nals.

*3 : Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler (separately available: recommended article).

Note

•DTV-format signals (480i, 480p, 720p, 1080i) can be input into this unit (Y, PB/B-Y, PR/R-Y input terminals). For details about DTV-format signals (480i, 480p, 720p, 1080i) compatible with this unit, refer to page 69.

■Computer signals

•Signals with the following resolutions can be input to the input terminal of COMPUTER IN-1 (PC) or COMPUTER IN-2 (G, B, R, H/Cs, V). (The following signals are preset.)

Screen resolution (standard name)				Horizontal frequency	Vertical frequency	Scanning method
640	× 400 (PC-9801)			24.8kHz	56.4Hz	Non-interlace
640	× 350		(VGA1)	31.5kHz	70.1Hz	Non-interlace
640	× 480		(VGA3)	31.5kHz	59.9Hz	Non-interlace
640	× 480		(Macintosh 13”)	35.0kHz	66.7Hz	Non-interlace
640 × 480 (VGA VESA)				37.5kHz	75.0Hz	Non-interlace
800	× 600 (SVGA1)			37.9kHz	60.3Hz	Non-interlace
800	× 600 (SVGA2)			48.1kHz	72.2Hz	Non-interlace
832	× 624		(Macintosh16”)	49.7kHz	74.6Hz	Non-interlace
1024		× 768 (XGA1)		48.4kHz	60.0Hz	Non-interlace
1024		× 768 (XGA2)		56.5kHz	70.1Hz	Non-interlace
1024		× 768 (Macintosh 19”)		60.2kHz	74.9Hz	Non-interlace
1152 × 870 (Macintosh 21”)				68.7kHz	75.0Hz	Non-interlace
1280		× 1024 (SXGA1)		64.0kHz	60.0Hz	Non-interlace
1280		× 1024 (SXGA2)		70.8kHz	67.0Hz	Non-interlace
1360		× 1024 (SXGA3: Mac Board)		80.0kHz	75.1Hz	Non-interlace

Notes

•Interlace signals are not handled.

•Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above may require adjustment depending on the video board used.

•When a signal other than listed above is input, the screen could be partially erased or an unneeded fold-over screen could appear.

•Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.

•Composite sync.(Cs) and G on sync. signals can not handled depending on the devices connected.

19

ENGLISH

G2000 p.15-23 19 99.11.20, 3:28 AM