74EN
TROUBLESHOOTING(Cont.)
SYMPTOM | POSSIBLE CAUSES | CORRECTIVE ACTION |
35. The LCD monitor | 35. •Certain FADE/WIPE, P.AE/ |
indications blink. | Effects, DIS and other |
| functions that cannot be |
| used together are selected at |
| the same time. |
35.•
(☞ pgs. 33, 36 – 43).
36. Coloured bright spots | 36. •The LCD monitor is made | 36. | |
appear all over the LCD | with |
| |
monitor. | technology. However, black |
| |
| spots or bright spots of light |
| |
| (red, green or blue) may |
| |
| appear constantly on the | ||
| LCD monitor. These spots |
| |
| are not recorded on the |
| |
| tape. This is not due to any |
| |
| defect of the unit. (Effective |
| |
| dots: more than 99.99 %) |
| |
37. The LCD monitor | 37. •During playback of the | 37. | |
indications are distorted. | unrecorded portion, High- |
| |
| speed Search and still | ||
| playback, LCD monitor | ||
|
| ||
| indications appear distorted. |
| |
| This is not a defect. |
| |
38. An unusual mark appears | 38. | 38. • Check the section of the | |
in the LCD monitor or the | manual that explains LCD | ||
viewfinder. | monitor/viewfinder | ||
| |||
|
| indications (☞ pgs. 79 – 81). | |
|
|
| |
39. An error indication | 39. •A malfunction of some kind | 39. • Remove the power supply | |
(E01 — E07) appears in | has occurred. In this case | (battery pack, etc.) and press | |
the LCD monitor or the | the camcorder’s functions | RESET button, and wait a few | |
viewfinder. | become unusable. | minutes for the indication to | |
|
| clear. When it does, you can | |
|
| resume using the camcorder. | |
|
| If the indication remains | |
|
| even though you repeat the | |
|
| above two or three times, | |
|
| please consult your nearest | |
|
| JVC dealer. | |
40. The charge indicator on | 40. •The temperature of the | 40. • To protect the battery, it is | |
the AC Power Adapter/ | battery is extremely high/ | recommended to charge it | |
Charger does not light. | low. | in places with a tempera- | |
| •Charging is difficult in | ture of 10°C to 30°C | |
| places subject to extremely | (☞ pg. 9). | |
| high/low temperatures. |
| |
41. The recording mode | 41. •This occurs when recording in | 41. | |
indicator “LP” blinks on | the LP mode is not available. |
| |
the LCD monitor or the | After the indicator blinks, the | ||
viewfinder. | recording mode switches to |
| |
| “SP” and recording goes on. |
| |
42. Picture does not appear | 42. •The viewfinder is pulled out. | 42. • Push the viewfinder back in. | |
on the LCD monitor. | •The LCD monitor's | • Adjust the brightness of the | |
| brightness setting is too | LCD monitor (☞ pg. 22). | |
| dark. | • If the monitor is tilted | |
|
| upward 180 degrees, open |
the monitor fully (☞ pg. 23).
43. When the image is 43. •This is not a malfunction. printed from the printer, a
black bar appears at the bottom of the screen.
43.• By recording with Digital Image Stabilizer set to “ON” (☞ pg. 33) this can be avoided.