For Digital Video Camera
Names of the parts
3 | Front glass |
|
|
| |
2 | 1 | |
| ||
|
| 6 5 |
3 |
| 9 |
|
| POWER |
|
| OFF |
|
| ON |
|
| ZOOM |
|
| START/STOP |
Bottom view |
|
|
4 |
| SNAP SHOT |
7 8 |
| |
|
1 Marine case front lid |
2 Main unit |
3 Buckle |
4 Grip attachment holes |
User’s Manual | ENGLISH |
Marine Case
Mounting method and operating method for each part
1 Tighten the camcorder’s grip strap. | Grip strap |
| |
2 Remove the four buckles on the marine |
|
case and open the front lid. |
|
3 Align the Power Lever with the “OFF” |
|
mark on the marine case. |
|
4 Set the camcorder’s Power Switch to |
|
“OFF”, then open the LCD monitor and |
|
insert the camera into the marine case.
Place the included
•Only the
•Remove the grip belt or strap from the camcorder before inserting it.
•If the camcorder’s Power Switch is set to “ ”, perform settings as required then insert the camcorder into the marine case.
5 Power lever (POWER) |
|
6 Recording start/stop button (START/STOP) |
|
7 Zoom lever (ZOOM) |
|
8 Snapshot button (SNAP SHOT) | Strap |
9 Grip strap |
|
5Fit the Zoom Lever projection on the marine case over the outer groove of the Power Zoom Ring on the camcorder, making sure that it is
securely fit.
If the camcorder’s Power Switch is not set properly when the camcorder is placed in the marine case, it could break and/or it could damage the Power Lever aligning boss on the marine case.
Fit the Zoom Lever projection over the Power Zoom Ring
POWER
OFF
ON
Projection
Power Zoom
Ring
Please read before use.
This marine case is a precision instrument designed to permit safe video recording under high water pressure. Please pay careful attention when handling the unit before and after use, as explained
6Before sealing the marine case, check that there is no sand, dirt, or
other foreign matter on the
unit.
Also make sure that the inserted silica gel bag is not pinched. If you dive with foreign matter trapped in these areas, water will leak.
in this user’s manual.
Each part of the marine case has been subject to strict controls during the manufacturing process, and the individual functions have faced stringent tests during the assembly process. Each marine case has also had to pass
Pre-use test
Be sure to perform the following 1.Before mounting the camcorder inside the marine case, dive with only the empty marine case and test for water leaks.
•Check for leaks at a depth of 3 m where there is no water pressure. Allow 5 or 6 minutes to ensure there are no leaks. Be sure to perform this test to ensure the safety of your camcorder.
2.The following are some common causes of water leaks: A. The marine case is used without attaching the
C. The
D. There is sand, dirt, hair or other foreign matter on the
surface of the
7Check that the
8Turn the marine case’s Power Lever in the
direction of the arrow to set the camcorder’s Power Switch to “ ” or “ ”.
• The camcorder’s Power Lamp lights.
9To start video recording, press the Record- ing Start/Stop Button.
To stop video recording, press it again.
•Press the Snapshot Button to perform Snapshot recording.
0The zoom can be adjusted with the Zoom Lever.
• Telephoto : turn the lever to the left ( )
•Wide angle : turn the lever to the right ( )
!When you are finished shooting, set the marine case’s Power Lever to “OFF” (in the direction of the arrow) to set the camcorder’s Power Switch to “OFF”.
•The camcorder’s Power Lamp goes out.
POWER
OFF
ON
ZOOM
START/STOP
POWER
OFF
ON
ZOOM
START/STOP
Recording Snapshot
start/stop button button
POWER
OFF
ON
ZOOM
START/STOP
F.The provided strap or silica gel bag is pinched inside the marine case when the lid is closed.
To protect your camcorder and ensure optimum use, keep the examples listed above in mind when using the marine case.
JVC accepts no responsibility for water leakage or damage to anything inside the marine case (camcorder, cassette, etc.) due to careless usage of this product. Be sure to follow correct procedures when using the marine case.
The
the front lid.
Refer to the camcorder’s instructions for more information.