Access Auto Timer | JVC HR-J430KR specification

32

TIMERRECORDING(cont.)

OK

6

q

°5

CH

1 2 3

4

5

6

7 8 9

Auto Timer

When the Auto Timer is set to ON the timer is automatically engaged when the VCR's power is turned off and automatically disengaged when the VCR is powered back on.

	ACCESS MAIN MENU
	SCREEN
1 Press MENU as many times as necessary.
	ACCESS FUNCTION SET
2	SCREEN
	Place the arrow next to "FUNCTION SET" by pressing
	CH5° or PUSH JOG5°, then press OK.
	ACCESS AUTO TIMER
	SCREEN
	Place the arrow next to "AUTO TIMER" by pressing
	CH5° or PUSH JOG5°, then press OK. Now skip to
3 step 2 of the procedure below.

0

TIMER

CH

OK

MENU

PUSH JOG

Or, during on-screen timer programming ...

		ACCESS AUTO TIMER
1		SCREEN
		In step 7 in the G-Code Timer Programming procedure
	(☞ pg. 27) or in step 7 in the On-Screen Timer Program-
	ming procedure (☞ pg. 29), press MENU.
2		SELECT MODE
		Place the arrow next to		AUTO TIMER
		your choice ("ON" or		AUTO TIMER
		your choice ("ON" or		=ON
		"OFF") by pressing CH5	°	=ON
	or PUSH JOG5°.		°	OFF
				PRESS (5,°) TO SELECT
				PRESS (MENU) TO END

		RETURN TO NORMAL
3		SCREEN
3		Press MENU as many times as necessary.

NOTE:

For safety, when AUTO TIMER is set to “OFF”, all other VCR functions are disabled while the Timer mode is engaged. To disengage the timer, press TIMER.

Image 32

JVC HR-J430KR manual Access Auto Timer

Contents

HR-J430KR Dear Customer Do not place the VCR Contents Basic Connections Make Corrections ClockSET Date and Time Tuner Perform Auto Channel SET Return to Normal Screen Access Tuner SET Screen Access AFC ScreenMake Selection Store Desired Channel Code Setup Access Main Menu Screen Access Initial SET Screen Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Input Guide Channel Number Return to Normal Return to G-CODE SET UP ScreenInput Receiving Channel Number Simple Playback Load a CassetteFind Program Start Point Start Playback Simple Recording Pause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow Motion Activate VARIABLE-SPEED Search Activate HIGH-SPEED SearchVariable-Speed Search Reverse Play High-Speed Search Engage Manual Tracking Mode Adjust Manual TrackingRE-ENGAGE Automatic Tracking Manual Tracking Superimpose Access Function SETAccess Superimpose Access Distant Code Skip Over Unwanted SectionsStart Repeat Stop Repeat Activate Instant Review Activate CounterMemory Return to Counter Position Zero Tape Position Indicator Relation to B Beginning or E End shows you where you are onPress REW, then press Timer within 2 seconds Next-Function Memory Access B.E.S.T. Picture System Screen Select ModeS.T. Picture System Preparation Recording Press and hold RECQuality of the tape Use, then recording Begins with the picture Level optimized Playback Tape in use Engage TV Mode Reset Counter to ZeroRecording Select Channel for Viewing Instant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC Enter G-CODE Number Code Timer ProgrammingAccess G-CODE Screen Data Engage Timer ModeCHECK/CORRECT Input On-Screen Timer Programming Access ON-SCREENAccess Program SET Screen Menu SET Program Information Example Disengage Timer Cancel a ProgramRE-ENGAGE Timer Check And Cancel Programs Access Auto SP/EP Auto SP/EP TimerPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OK Access Auto Timer Auto Timer Special Features 19, 20 Edit From a Camcorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Control Two JVC VCRs Random As- semble Editing Prepare for Editing END R.A. Edit Start R.A. Edit Troubleshooting Cassette gets stuck partway Timer again Re-perform the G-Code setup Doesn’t work properlyWhen scanning channels, some Has not been programmed correctly Cassette is automatically Questions and Answers EIA monochrome signal Maximum recording time 210 min. with ST-210 video630 min. with ST-210 video Frequency-synthesized tuner Ramdom Assemble Editing connector pg Index Remote Control Provided Front Display Panel HR-J430KR