Manuals / JVC / TV and Video / DVD Player

JVC HR-J674EU 52 EN, Other Problems, TROUBLESHOOTING cont, Symptom, Possible Cause

Models: HR-J674EU

1 56

Download 56 pages 42.91 Kb

Page 52

52 EN

52 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 42).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Connect the TV aerial cable to the
	recorder’s memory.	to the recorder when Auto Set Up was	recorder properly and turn off the recorder
		performed.	power once, then turn the recorder power
			back on again. The recorder will try Auto
			Set Up again ( pg. 8).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 52

JVC HR-J674EU instruction manual 52 EN, Other Problems, TROUBLESHOOTING cont, Symptom, Possible Cause, Corrective Action

Contents

VIDEO CASSETTE RECORDER CONTENTSENGLISH Safety Precautions SAFETY FIRST2 EN WARNING DANGEROUS VOLTAGE INSIDEPage 4 EN FRONT VIEWREAR VIEW INDEXFRONT DISPLAY PANEL ON-SCREEN DISPLAYREMOTE CONTROL How To Use6 EN Operating JVC TVsINSTALLING YOUR NEW RECORDER A Check the contentsBasic Connections B Situate the recorderAuto Set Up INITIAL SETTINGS8 EN Auto Channel Set/Auto Clock Set/ Auto Guide Program Number SetD Perform Auto Set Up C Select the languageOn the front display panel On the on-screen displayPreset Download A Perform Preset DownloadINITIAL SETTINGS cont 10 ENLanguage for the on-screen display INFORMATIONJust Clock A Access the Main Menu screen B Access the Country Set screenLanguage 12 ENSatellite Receiver Control Setting Installing Satellite ControllerSAT CONTROL SET A Situate the Satellite ControllerSetting satellite receivers brand and channel B Access the Main Menu screen on the recorderC Access the Initial Set screen D Access the Sat Control Set screenTV Auto Power On NexTView LinkVCR Auto Standby Direct RecBasic Playback 16 ENA Load a cassette B Find the programme start pointPlayback Features Slow MotionHigh-Speed Search Variable Speed Search2 Adjust the tracking manually 18 ENManual Tracking Instant ReViewIndex Search Skip SearchNext Function Memory Repeat PlaybackBasic Recording 20 ENRecording Resume Function B Choose a programmeRecording Features Instant Timer Recording ITR2 Engage the ITR mode Watching Another2 Reset the counter 22 ENTape Remaining Time Elapsed Recording Time IndicationB.E.S.T. Picture System PlaybackRecording DURING B.E.S.T B.E.S.T. COMPLETESHOWVIEW Timer Programming A Access the SHOWVIEW screenC Access the SHOWVIEW Program screen TIMER RECORDINGE Set the VPS/PDC mode G Engage the recorder’s timer modeD Set the tape speed. HR-J670/671/672/673/674/470/ 472EU only F Return to the normal screenExpress Timer Programming B Access the Programme screenTIMER RECORDING cont 26 ENH Set the VPS/PDC mode J Engage the recorder’s timer modeVPS/PDC Recording F Enter the channel positionTo cancel or change a programme Check, cancel and change programmesA Disengage the timer mode C Access the Programme screen/displayWhen programmes overlap each other C Cancel or change programme settingA Confirm the overlapping programmes B Select the programme to modifyA Select the L-2 SELECT mode C Engage the Auto Satellite Programme Recording modeProgramme Recording Automatic SatelliteB Set the recorder’s input mode C Set the edit modeEdit From A Camcorder EDITINGB Set the input mode of recording deck Another Video Recorder32 EN D Start the source playerConnecting To A Satellite Receiver SYSTEM CONNECTIONSSatellite receiver Decoder Back of recorder Back of TVConnecting/Using A Decoder A Select the input mode34 EN B Connect the decoderConnecting/Using A Stereo System HR-J670/671/672/673/674EU onlyMake connections CAUTIONSMode Set B Access the Mode Set screenC Select the mode D Select the mode setting8 AUTO TIMER 8 B.E.S.T8 PICTURE CONTROL 8 O.S.DSUBSIDIARY SETTINGS cont 8 AUTO SPLP TIMER8 POWER SAVE 38 EN8 L-2 SELECT 8 COLOUR SYSTEMPAL/NTSC About NTSC PlaybackB Access the Main Menu screen C Access the Auto Channel Set screenSUBSIDIARY SETTINGS cont Tuner SetG View the Confirmation screen F Perform Auto Channel SetH Return to the normal screen B Access the Confirmation screen 42 ENManual Channel Set C Select the channel positionWhen Receiving A Scrambled Broadcast A Select the decoder modeD Change the decoder setting Delete A ChannelFine-Tuning Channels Already Stored D Switch the stationsB Access the Manual Channel Set screen C Perform tuningSTATION NAME TV Station And ID ListSTATION NAME A Access the Video Channel Set mode D Exit the Video Channel Set modeVideo Channel Set 46 ENSHOWVIEW Setup B Access the Initial Set screenC Access the Guide Program Set screen Guide Program Number SetD Access the Clock Set screen Clock Set48 EN B Access the Main Menu screenE Set the date and time F Set Just ClockG Set the source channel position for clock data H Start the clock operationPOWER TROUBLESHOOTINGSYMPTOM 50 ENTIMER RECORDING RECORDINGSYMPTOM SYMPTOMOTHER PROBLEMS TROUBLESHOOTING cont52 EN SYMPTOMTIMER RECORDING QUESTIONS AND ANSWERSPLAYBACK RECORDINGSPECIFICATIONS 54 ENLIST OF TERMS Auto Set Up - referring to the front display panel FOR MORE INFORMATION SEE INSTRUCTIONS pg