JVC LPT0800-001B Audio Dubbing, Edit to or from Another Video Recorder, A Make connections

You can use a camcorder as the source player and your video recorder as the recorder.

AMake connections

aIf the camcorder has no S-VIDEO output connector...

... connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's front panel AUDIO/VIDEO input connectors.

bIf the camcorder has an S-VIDEO output connector...

... connect the camcorder's S-VIDEO OUT and AUDIO OUT connectors to the recorder's front panel S-VIDEO(S-2) and AUDIO input connectors. The recorder's rear panel S-VIDEO IN and AUDIO IN input connectors are also available.

●When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder.

●When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder's instruction manual for operating procedure.

BSet recorder’s input mode

Press number key “0” and/or PR +/– to select “F-1” for the AUDIO/VIDEO input connectors, or “S-2” for the AUDIO/S- VIDEO input connectors, depending on the connectors being used.

CSelect “EDIT” for picture control set mode

Follow the “Picture Control” section on page 15, then select “EDIT.”

DStart camcorder

Engage its Play mode.

EStart recorder

Engage its Record mode.

Edit to or from Another Video Recorder

TV Receiver Player Your recorder

VIDEO CHANNEL

RF Cable (provided)		AV Cable
		(not provided)
	Another recorder
	Recorder
Recorder	Your recorder	TV Receiver

AV Cable	VIDEO
	CHANNEL
(not provided)

RF Cable (provided)

Another recorder

Player

You can use your video recorder as the source player or the recording deck.

AMake connections

Connect the player's AUDIO/VIDEO OUT connector to the recorder's AUDIO/VIDEO IN connector.

●Use the L connector for monaural connection.

BSet recording deck’s input mode

Set to AUX. With this video recorder, press number key “0” and/or PR +/– to select depending on the connector being used — “L-1” for the rear panel VIDEO/AUDIO input connectors, or “F-1” for the front panel VIDEO/AUDIO input connectors.

CSelect “EDIT” for picture control set mode

Follow the “Picture Control” section on page 15, then select “EDIT.”

DStart source player

Engage its Play mode.

ESet recording deck

Engage its Record mode.

NOTES:

●To edit, both the player and the recorder must be of the same colour system. Select the appropriate colour system ( 15).

●When you use this recorder as the player for editing, be sure to set “O.S.D.” to “OFF” before starting ( 15).

●All necessary cables can be obtained from your dealer.

●NTSC tapes being played back in the “NTSC]PAL” mode ( 16) cannot be dubbed to another recorder.

●When you dub an NTSC tape using your recorder as the

playback deck, select “NTSC 3.58” (or “NTSC 4.43”) for “NTSC” setting ( 15).

●When you select “EDIT” to dub tapes, be sure to select “AUTO”

(or “NORM” when the B.E.S.T. function is set to “OFF”) after you finish dubbing the tapes ( 15).

●If you are using another recorder with S-Video and Audio input/ output connectors, you can connect those connectors to this recorder's S-VIDEO IN/S VIDEO OUT and AUDIO IN/OUT connectors.

When Using Your Video Recorder As The Source Player ...

... connect its rear panel S VIDEO OUT and AUDIO OUT connectors to the recording deck's S-Video and Audio input connectors.

When Using Your Video Recorder As The Recording Deck ...

... connect its front panel S-VIDEO and AUDIO input connectors to the source player's S-Video and Audio output connectors. Then, set the recorder's input mode to “S-1”.

Audio Dubbing

CD Player etc.

Mixer output Audio mixer

Original sound

AUDIO OUT

— 20 —