JVC HR-VP48U Input receiving channel number, Engage timer recording standby mode, Press SP/EP

GUIDE CHANNEL SET

GUIDE CH: 12

VCR CH : –––

PRESS NUMBER KEY (0–9)

OR (5,°), THEN (OK)

PRESS (PROG.) TO END

EN 25

4Input receiving channel number

The guide channel number, which is

assigned to the TV or cable station for the

PlusCode number that you entered in step 3, will appear automatically on the Guide Channel Set screen.

Press the Number keys (or CH +/– or SHUTTLE PLUS 5°) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR, then press OK.

The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously.

If you receive your channels through a cable box, select the cable box output channel — the channel on which you view the cable box programs on the TV.

7 Return to normal screen Press PROG. or OK.

“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

•If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made.

The Program Check screen appears and conflicting programs will start blinking.

You can now correct the conflicting programs. See “When programs overlap each other” on page 31.

8Engage timer recording standby mode

Press TIMER.

The VCR turns off automatically and “ä” is displayed on the front display panel.

To use the VCR while it is in timer recording standby mode

5 Check program date The PlusCode number you entered and the corresponding timer recording program is displayed on the Program screen. Check to make sure it is accurate.

PROGRAM 1

(VCR PLUS+ 12345678)

START	STOP
8:00PM	= 10:00PM
DATE	CH
12/24/00	12 SP
SAT

PRESS (8=DAILY, 9=WEEKLY STOP+/– = STOP TIME, SP/EP)

PRESS (PROG.) TO END

Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR.

DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want.

When “AUTO TIMER” ( pg. 33) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

To change the stop time, press STOP +/–. To timer-record daily (Monday–Friday) or weekly serials, press DAILY (M–F)(number “8”) or WEEKLY (number “9”). “DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes each corresponding display disappear.

If you made a mistake, press CANCEL to access the VCR Plus+ screen again and input the correct PlusCode number.

If an incorrect PlusCode number or the one for a broadcast already finished has been inputted, “ERROR” is displayed for about 5 seconds, then the VCR Plus+ screen reappears.

6Set tape speed

Press SP/EP.

IMPORTANT

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH number will be displayed on the Program screen in step 5. When this happens, set the correct guide channel number for that station. ( pg. 26, “VCR Plus+ Setup”)

NOTES:

Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost if it lasts for more than 3 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1.This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting.

2.If the clock time and channel setting are restored correctly, each timer program you have made will start unless its end

time already passes.

To timer-record cable channels received through a cable box, be sure to keep the cable box turned on with the correct channel selected.