Manuals / JVC / TV and Video / VCR

JVC LPT0616-001A 86 EN, Other Problems, TROUBLESHOOTING cont, Symptom, Possible Cause

Models: LPT0616-001A

1 92

Download 92 pages 22.62 Kb

Page 86

86 EN

86 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 76).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

6.	The remote control won’t operate the	● The remote control brand setting is	Re-set the remote control to the correct
	TV or satellite receiver.	incorrect.	brand. ( pg. 61, 62)

7.	No picture appears when you connect		Turn off the recorder or the connected
	a device to DV IN/OUT connector.		appliance once, then turn it on again.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 86

JVC LPT0616-001A specifications 86 EN, Other Problems, TROUBLESHOOTING cont, Symptom, Possible Cause, Corrective Action

Contents

INITIAL SETTINGS CONTENTSSAFETY FIRST TIMER RECORDING2 EN Safety PrecautionsSAFETY FIRST WARNING DANGEROUS VOLTAGE INSIDEPage INDEX 4 ENFRONT VIEW REAR VIEW INDEX cont 6 ENFRONT DISPLAY PANEL ON-SCREEN DISPLAY for DV deck ON-SCREEN DISPLAY for VHS deckINDEX cont REMOTE CONTROL8 EN How To Use Remote Control LCDBasic Connections A Check the contentsINSTALLING YOUR NEW RECORDER 10 ENB Connect the recorder to mains S-VIDEO ConnectionA Connect the recorder to TV 8To connect to a TV with S-VIDEO/AUDIO IN connectors12 EN Auto Set UpINITIAL SETTINGS Auto Channel Set/Auto Clock Set/ Auto Guide Program Number SetOn the front display panel D Perform Auto Set UpC Select the language On the on-screen displayINITIAL SETTINGS cont Preset DownloadA Perform Preset Download 14 ENJust Clock INFORMATIONLanguage for the on-screen display Language A Access the Main Menu screenB Access the Country Set screen 16 ENSAT CONTROL SET Satellite Receiver Control SettingInstalling Satellite Controller A Situate the Satellite ControllerC Access the Initial Set screen Setting satellite receivers brand and channelB Access the Main Menu screen on the recorder D Access the Sat Control Set screenVCR Auto Standby TV Auto Power OnNexTView Link Direct RecVHS deck Basic Playback20 EN A Load a cassetteD Set the tape speed Basic RecordingC Choose a programme E Start recordingSlow Motion Playback Features22 EN Still Picture/Frame-By-Frame PlaybackIndex Search High-Speed Turbo SearchVariable Speed Search Skip SearchRepeat Playback 24 ENNext Function Memory 1 Start playbackSoundtrack Selection 2 Adjust the tracking manuallyManual Tracking 1 Override automatic tracking26 EN Recording FeaturesInstant Timer Recording ITR Record One Programme While Watching AnotherElapsed Recording Time Indication 2 Reset the counterTape Remaining Time 1 Set the counter displayReceiving Stereo and Bilingual Programmes 28 ENRetake 1 Engage the Record-Pause modeRecording B.E.S.T. Picture SystemPlayback VHS deckB Select the DV deck 30 ENDV deck PLAYBACK/RECORDING ON DV DECKA Load a cassette Basic RecordingDV deck B Select the DV deckPlayback Features 32 ENPLAYBACK/RECORDING ON DV DECK cont Clean the video heads using a dry cleaning cassette - M-DV12CL - whenNext Function Memory High-Speed Turbo SearchVariable Speed Search Soundtrack SelectionInstant Timer Recording ITR 34 ENRecording Features DV deckOn-screen Display Time CodeReceiving Stereo and Bilingual Programmes ReceivedTIMER RECORDING SHOWVIEW Timer ProgrammingD Access the SHOWVIEW display 36 ENH Set the tape speed K Engage the recorder’s timer modeG Check the programme data I Set the VPS/PDC modeE Access the Programme screen Express Timer ProgrammingD Access the SHOWVIEW screen TIMER RECORDING contH Enter the programme date M Engage the recorder’s timer modeVPS/PDC Recording I Enter the channel position40 EN 24 Hour Express Timer ProgrammingC Engage the recorder’s timer mode A Enter the programme modePage A Disengage the timer mode To cancel or change a programmeCheck, cancel and change programmes C Access the Programme screen/displayA Confirm the overlapping programmes When programmes overlap each otherC Cancel or change programme setting B Select the programme to modifyfrom DV to VHS Tape Dubbing44 EN Dubbing An Entire CassetteDubbing An Entire Cassette from VHS to DVTape Dubbing A Load cassettesD Locate the start point on the DV deck Normal Dubbing46 EN E Prepare the VHS deck for dubbingNormal Dubbing D Locate the start point on the VHS deckE Prepare the DV deck for dubbing from VHS to DVA Make connections 48 ENEdit From A Camcorder B Select the recording deckRecorder About DV IN/OUT connectorA If the camcorder has no S-VIDEO output connector VIDEO inputAdvantages of S-VHS video recorders Another Video Recorder50 EN C Set the input mode of recording deckAnother recorder PlayerRecorder PlayerC Select the output or input mode for the AV1 L-1 IN/OUT connector L-1 OUTPUT and L-1 INPUT SettingB Access the Output/Input Set screen Output/Input SetDECODER connector L-2 SELECT SettingVHS F-1 INPUT Setting A Select the input mode for the VIDEO S-VIDEO connectorVHS Audio Dubbing Audio Dubbing54 EN DV Audio DubbingE Locate the start point C Select the recording deckD Set the recorder’s input mode F Engage the Audio Dubbing modeVHS Insert Editing Insert Editing56 EN DV Insert Editing SP mode onlyF Engage the Insert Editing mode AV Insert Editing VHS deck onlyD Prepare the recording cassette G Start Editing58 EN C Access the R.A.Edit screenRandom Assemble Editing 64-programme Editing Memory 8 programmes x 8 scenesH Prepare the VHS deck for dubbing F Locate the end pointG Prepare the source tape I Start Random Assemble EditingB Change the remote control code Remote Control FunctionsRemote A/B/C/D Code Switching C Set the remote control codeA Set the TV brand code TV Multi-Brand Remote ControlControl Your TV Using Additional Buttons B Operate the TV62 EN Satellite Receiver Multi-Brand Remote ControlREMOTE CONTROL cont A Set the satellite receiver brand codeC Start playback SYSTEM CONNECTIONSB Select the deck Connecting To A Printer64 ENSYSTEM CONNECTIONS cont Connecting To A Satellite ReceiverSimple Connections Back of TVSatellite receiver Perfect ConnectionsBack of TV DecoderA Select the input mode Connecting/Using A Decoder66 EN B Connect the decoderCAUTIONS Connecting/Using A Stereo SystemMake connections AUX IN or TAPE MONITORSUBSIDIARY SETTINGS B Access the Mode Set screenD Select the mode setting Mode SetMODE SET 8 AUTO TIMER8 POWER SAVE 8 O.S.D70 EN SUBSIDIARY SETTINGS cont8 AUTO SPLP TIMER VHS MODE SET8 S-VHS VHS MODE SET cont8 DIGITAL 3R 8 S-VHS ETSUBSIDIARY SETTINGS cont 72 EN8 COLOUR SYSTEM using this video recorder as the source player for editing8 12BIT MODE DV MODE SET8 SOUND MODE 8 AUDIO RECTuner Set B Access the Main Menu screenC Access the Auto Channel Set screen 74 ENH Return to the normal screen F Perform Auto Channel SetG View the Confirmation screen Manual Channel Set B Access the Confirmation screen76 EN C Select the channel positionDelete A Channel When Receiving A Scrambled BroadcastD Change the decoder setting Change Station Channel PositionB Access the Manual Channel Set screen Fine-Tuning Channels Already StoredD Switch the stations C Perform tuningSTATION NAME TV Station And ID ListSTATION NAME RTBF1 or80 EN D Access the Clock Set screenClock Set B Access the Main Menu screenG Set the source channel position for clock data E Set the date and timeF Set Just Clock H Start the clock operationC Access the Guide Program Set screen SHOWVIEW System SetupB Access the Initial Set screen 82 ENSYMPTOM POWERTROUBLESHOOTING TAPE TRANSPORTRECORDING TROUBLESHOOTING cont84 EN SYMPTOMPOSSIBLE CAUSE TIMER RECORDINGSYMPTOM CORRECTIVE ACTIONTROUBLESHOOTING cont OTHER PROBLEMS86 EN SYMPTOMPLAYBACK TIMER RECORDINGQUESTIONS AND ANSWERS RECORDINGSPECIFICATIONS 88 ENLISTE OF TERMS 90 EN MEMOPage Auto Set Up - referring to the front display panel