JVC LVT1364-002B Getting Started

6

Getting Started

Unpacking

After unpacking, check to be sure that you have all the

following items.

The number in parentheses indicates the quantity of each

piece supplied.

•FM antenna (1)

•AM (MW) loop antenna (1)

•Remote control (1)

•Batteries (2)

If any item is missing, consult your dealer immediately.

Connecting AM (MW) and FM Antennas

1

Attach the supplied FM antenna to the FM

75 Ω COAXIAL terminal.

Fasten in up the position which gives you the best

reception, then fix it on the wall, etc.

2

Connect the supplied AM (MW) loop

antenna to the AM LOOP terminal.

Place the antenna away from the unit and adjust its

position for the best reception.

For better reception of both FM and AM (MW)

• Make sure the antenna conductors do not touch any other

terminals or connecting cords.

•Keep the antennas away from metallic parts of the unit,

connecting cords, and the AC power cord.

About the supplied FM antenna

The FM antenna supplied with this unit can be used as temporary

measure. If reception is poor, you can connect an outdoor FM antenna.

To connect an outdoor FM antenna

Before connecting the antenna, disconnect the supplied FM antenna.

Do not connect the AC power cord until all other

connections have been made. Continued

Connecting Speakers

You can connect the speakers using the speaker cords.

1

Hold the clamp of the speaker terminal.

2

Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: red cord to

ª and black cord to ·.

3

Release your finger from the clamp.

IMPORTANT:

•Use only speakers with the same speaker impedance as

indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one

speaker terminal.

Red

Speaker

cord

Left speaker

Right speaker

Red

Black

Black

Speaker

cord

12,3

Ò

Â

Outdoor FM antenna

(not supplied)

Coaxial cable (not supplied)

A 75 Ω antenna with coaxial type connector

(IEC or DIN 45325) should be used.

AMLOOP

FM 75Ω

COAXIAL

2

1

AMLOOP

FM 75Ω

COAXIAL

FM antenna (supplied)

AM (MW) loop antenna (supplied)

06-07_UX-G4_UX-G3[B]3.p65 05.2.14, 8:26 PM6

Contents

Main G-1 Warnings, Cautions and Others UX-G4/UX-G3 1 cm 10 cm SAFETY INSTRUCTIONS SOME DOS AND DONTS ON THE SAFE USE OF EQUIPMENT 1 Power sources Moisture condensation Others Introduction Contents Location of the Buttons and Controls Main Unit Display window Main unit ON DAILY 123 452316789pq r o uy tsa;i w Remote Control Getting Started Unpacking Connecting AM (MW) and FM Antennas Attach the supplied FM antenna to the FM 75 COAXIAL terminal. Connect the supplied AM (MW) loop antenna to the AM LOOP terminal. 7 Connecting Other Equipment To connect an audio equipment Putting the Batteries into the Remote Control NOW you are ready to plug in the unit. Common Operations Setting the Clock and Repeat steps Press CLOCK/TIMER. Selecting the Source Adjusting the Volume Fade-Out Muting (FADE MUTING) Selecting the Sound Modes Reinforcing the Bass Sound Playing Back Discs When playing CD-Rs or CD-RWs Notes for MP3 files General notes Basic Disc Operations To stop playing for a moment Repeat step To go to another track To go to another track directly using the number buttons Repeating TracksRepeat Play Press REPEAT repeatedly before or during playback. Press CD 3/8. To check the program contents To modify the program Displaying the Remaining Time during Playback Press REMAIN repeatedly. Playing at RandomRandom Play Press RANDOM. To play both sidesReverse Mode Playing Back Tapes Tuning in to a Station Press FM/AM to select either FM or AM (MW). to To preset more stations, repeat steps Listening to FM and AM (MW) Broadcasts Presetting Stations Tune in to the station you want to preset. Press SET. Press PRESET GROUP or PRESET GROUP to select a preset number, then press SET. Tuning in to a Preset Station Press FM/AM to select either FM or AM (MW). Press PRESET GROUP or PRESET GROUP repeatedly to select a preset number. To tune in to a preset station directly using the number buttons Receiving FM Stations with RDS Searching for Programs by PTY Codes (PTY Search) Press RDS SEARCH repeatedly until the PTY code you want appears on the display. Press or 4 (or UP or DOWN 4 on the unit). Using an External Equipment Start playing the sourceFM, AM (MW), or auxiliary equipment connected to AUX jack. Press REC (recording). Press TAPE . To record on both sidesReverse Mode Recording Recording on a Tape On the unit ONLY: Put a recordable cassette in with the exposed part of the tape down. Close the cassette holder gently. Recording Discs Disc Synchronized Recording Using the Timers Using Daily Timer and Recording Timer How the Timer actually works Before you start... Set the on-time you want the unit to turn on. Using Snooze Timer On the unit ONLY: Press DAILY TIMER/ SNOOZE while Daily Timer is in operation. Using Sleep Timer How the Sleep Timer actually works Press SLEEP. Wait for about 5 seconds after specifying the length of time. Maintenance General notes Cleaning the unit Handling discs Handling cassette tapes Troubleshooting Symptom Possible Cause Action Amplifier Section Specifications