General

 

Troubleshooting

 

 

 

 

 

 

 

 

 

 

 

Symptom

Check Points

Action

 

 

 

 

 

 

 

 

 

Colors in the monitor screen

• Is the SC phase adjusted properly?

P. 13

 

 

 

are abnormal. (During

 

 

 

 

 

genlocking)

 

 

 

 

 

 

 

 

 

 

 

Synchronization is not

• Are the Tri-level sync signal or BB signals applied to the

P. 13

 

Video

possible.

GENLOCK INPUT connectors?

 

 

troubles

 

• Is the VTR playback signal supplied directly without passing

 

 

 

 

 

through a TBC?

 

 

 

 

 

 

 

 

 

 

SD SDI signal level is not

• Is the SETUP LEVEL setting of camera set to the value same as

P. 26

 

 

 

outputted correctly (RM-

SETUP LEVEL setting of RM-HP250AU?

 

 

 

 

HP250AU only)

 

 

 

 

 

 

 

 

 

 

 

Pressing the corresponding

• Functions that are not available on the camera cannot be

Check the

 

 

 

button cannot start the

controlled.

camera

 

 

 

operation.

 

functions

 

 

 

<EXT> is displayed on the LCD.

 

again.

 

 

 

 

 

 

 

 

 

The LCD display keeps on

• Are cables connected properly?

P. 8

 

 

 

displaying "NOW INITIALIZING

• Is the power switch of the camera set to ON?

P. 9

 

 

 

JUST A MOMENT".

 

P. 10

 

 

 

 

 

 

 

 

 

The LCD display keeps on

• Are cables connected properly?

P. 8

 

 

 

display “PLEASE CHECK THE

• Is the power switch of the camera set to ON?

P. 9

 

 

 

CAMERA”.

(When power of camera is turned off while RM-HP250 is on,

P. 10

 

 

 

 

“PLEASE CHECK THE CAMERA” will be displayed after about 20

 

 

 

 

 

seconds if RM-HP250 is operated.

 

 

 

 

 

In addition, when turning on RM-HP250 while the power switch of

 

 

 

 

 

camera is off, similar display will appear after about 30 seconds. )

 

 

 

 

 

 

 

 

 

 

LCD display shows "---".

• The connected camera does not have the assigned function.

P. 25

 

 

 

 

Check the camera functions again and assign the proper

 

 

 

 

 

functions to the F1 to F4 keys.

 

 

 

 

 

 

 

 

 

 

White-balance adjustment

• Is the W.BAL switch set to A or B?

P. 18

 

Control

cannot be started.

• Is FAS or FAW ON (which is indicated by the lighting of the AUTO

 

 

 

light)?

 

 

troubles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The white balance adjustment

• Are the color temperature filters and lighting conditions appropriate?

P. 18

 

 

 

will not complete.

• Does the object have colors?

 

 

 

 

 

 

 

 

 

 

The tally lamp does not light.

• Is the tally system of the RM-HP250 compatible with that of the

P. 14

 

 

 

 

camera system?

 

 

 

 

 

The RM-HP250 has been set to the voltage supply at the factory.

 

 

 

 

 

If it is required to use the TALLY input in the contact supply mode,

 

 

 

 

 

the setting of the internal circuitry should be changed ; consult the

 

 

 

 

 

nearest JVC-authorized service agent.

 

 

 

 

 

 

 

 

 

 

Incorrect operation even when

• Is the STUDIO cable of KA-HD250U pulled out or loose?

Connect the

 

 

 

FAS button is ON.

 

cable properly.

 

 

 

 

 

 

 

 

 

"E.02" will be displayed on RM-

• Are cables connected properly?

P. 8

 

 

 

LP25U

• Is the power switch of the camera set to ON?

P. 9

 

 

 

 

(When power of camera is turned off while RM-HP250/RM-LP25U is

P. 10

 

 

 

 

on, similar display will appear after about 10 seconds.)

 

 

 

 

 

 

 

 

 

 

OPERATE button of RM-LP25U

• Are cables connected properly?

P. 8

 

 

 

keeps blinking.

• Is the power switch of the camera set to ON?

P. 9

 

 

 

 

(When turning on RM-HP250/RM-LP25U while the power switch of

P. 10

 

 

 

 

camera is off, the OPERATE button will keep blinking.)

 

 

 

 

 

 

 

 

31