Operation

Exemplary System

Connection:

Connect the remote control unit cable to the REMOTE terminal.

To reduce the emission of unwanted radio waves, be sure to attach the provided clamp filter as shown in the figure below.

●Attach the clamp filter as close to this device as possible, as shown in the figure.

Clamp filter

GY-HD200/GY-HD250

Wind once

 

HD CAMERA RECORDER

To REMOTE Terminal

 

 

Switcher

Mini Din 6-Pin

Cable

TALLY(PGM)

TALLY(PVW)

OPERATE

 

 

LOCK

 

 

BARS

 

 

 

PART

 

 

 

 

 

 

OFF FULL

 

 

 

SCENE FILE

 

 

 

SPEED

1

2

3

4

5

 

 

 

PART

 

SHUTTER

 

 

 

NORMAL

1/100

1/250

1/1000

1/2000

VARIABLE

1/120

1/500

0dB

 

 

GAIN

 

 

 

3dB

6dB

9dB

12dB

15dB

18dB

-3dB

-6dB

ALC

LOLUX

VARIABLE

 

LEVEL

 

 

LEVEL

GAMMA

LEVEL

DETAIL

KNEE POINT

AUTO

 

 

 

 

 

 

KNEE

BLACK

 

WHITE BALANCE MODE

 

COMPRESS

STRETCH

MANUAL

PRESET

FAW

AW A

AW B

R

WHITE PAINT

 

PAINT

AUTO WHITE

 

B

 

R

BLACK PAINT

 

PAINT

AUTO BLACK

 

B

 

 

 

 

PART

 

 

 

 

 

 

OVER

 

OPEN

PRESET

IRIS MODE

 

 

 

 

LEVEL

 

 

 

 

 

 

FULL

AUT

 

 

 

PRE

 

IR

 

IS

 

SET

AUTO

LEV

 

 

 

 

 

 

 

 

FULL

TALLY

CALL PREVIEW

UNDERCLOSE

MASTER

BLACK

RM-LP25U

REMOTE CONTROL PANEL

Note:

●Turn the power off when connecting.

Setup

1 Set up by connecting this product to GY-HD250or GY-HD200.

●Connect according to the instruction manual of the devices in use, and set accordingly.

2 Set this product as follows:

●Set the [LOCK] switch to AOFFB.

●Set the [OPERATE] button to AOFFB (light off).

AOFFB

OPERATE

 

 

LOCK

 

 

BARS

AOFFB

 

 

PART

 

 

 

 

 

 

 

 

 

(Light off)

 

 

OFF FULL

 

 

 

 

SCENE FILE

 

 

 

SPEED

 

 

 

 

 

1

2

3

4

5

 

 

 

PART

 

SHUTTER

 

 

 

NORMAL

1/100

1/250

1/1000

1/2000

VARIABLE

1/120

1/500

Note:

●To enable iris control using this product, set the lens iris mode of the camera to AAUTOB or AAB.

3 Press the [OPERATE] button.

●The [OPERATE] button starts to blink in orange, and initial communication with the connected camera starts.

●After initial communication is complete, the [OPERATE] button switches to solid orange. Control of the camera using this product is now enabled.

AONB

OPERATE

 

LOCK

BARS

(Light on)

 

 

PART

 

 

 

 

 

 

 

 

 

OFF

FULL

 

 

 

 

SCENE FILE

 

SPEED

 

1

2

3

4

5

Memo:

●The time required for initial communication may be extremely short for some cameras, such that the button only appears blinking for an instant, after which it lights up in solid orange.

14