JVC RX-6020VBK manual SPK Digital Auto

Basic Settings

From the remote control:	/DIGITAL
	ANALOG

Press ANALOG/DIGITAL.

The current setting indication appears on the display.

•Each time you press the button, the input mode alternates between the analog input (“ANALOG”) and the digital input (“DIGITAL AUTO”).

DIGITAL AUTO : Select this for the digital input mode. The receiver automatically detects the incoming signal format. (The DIGITAL AUTO indicator lights up on the display, then the digital signal indicator for the detected signals lights up.)

ANALOG : Select this for the analog input mode. (Initial setting when shipped from the factory.)

If the following symptoms occur while playing Dolby Digital or DTS Digital Surround software with “DIGITAL AUTO” selected, follow the procedure below:

–Sound does not come out at the beginning of playback.

–Noise comes out while searching or skipping chapters or tracks.

1Press INPUT DIGITAL (or ANALOG/DIGITAL on the remote control).

“DIGITAL AUTO” appears on the display.

INPUT DIGITAL	ANALOG
	/DIGITAL

On the front panel	From the remote control
2 Press CONTROL UP 5/DOWN ∞ to select		Remote
“DOLBY DIGITAL” or “DTS SURROUND”
		NOT
while “DIGITAL AUTO” still remains on the
display.		DOWN UP
		CONTROL

• Each time you press the button, the digital input mode changes as follows:

When “DOLBY DIGITAL” or “DTS

SURROUND” is selected, “DIGITAL AUTO” goes off.

	SPK
DIGITAL AUTO	L	C	R
	S.WFR LFE
DIGITAL	LS	S	RS

CH-

DIGITAL AUTO DTS SURROUND

DOLBY DIGITAL

•To play back software encoded with Dolby Digital, select “DOLBY DIGITAL.”

•To play back software encoded with DTS Digital Surround, select “DTS SURROUND.”

Note:

When you turn off the power or select another source, “DOLBY DIGITAL” and “DTS SURROUND” are canceled and the digital input mode is automatically reset to “DIGITAL AUTO.”

The following are the analog/digital signal indicators on the display to indicate what type of the signal comes into the receiver.

ANALOG : Lights when the analog input is selected.

LINEAR PCM : Lights when Linear PCM signals come in. DIGITAL : • Lights when Dolby Digital signals come in.

•Flashes when “DOLBY DIGITAL” is selected for software not encoded with Dolby

Digital signals.

: • Lights when DTS signals come in.

•Flashes when “DTS SURROUND” is selected for software not encoded with DTS signals.

Note:

When “DIGITAL AUTO” cannot recognize the incoming signals, no digital signal indicator lights up on the display.

Setting the Speaker Information Remote

NOT

To obtain the best possible sound or effect from Surround modes (see page 21-23), register the following speakers and subwoofer information after all connections are completed.

The following are items you can set:

•Subwoofer information—SUBWOOFER

•Speaker size—FRNT SP, CNTR SP, REAR SP

•Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS

•Crossover frequency—CROSS

•Low frequency effect attenuator—LFE ATT

•Dynamic range compression—D. COMP

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

“NO” for the subwoofer, “LARGE” for the front speakers, and “SMALL” for the center and rear speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions.

Subwoofer information

Register whether you have connected a subwoofer or not.

1 Press SETTING repeatedly until
		T	SETTING
“SUBWOOFER” (with the current
setting) appears on the display.
2 Press CONTROL UP 5/DOWN ∞	DOWN UP
		CONTROL
to register whether you have
connected a subwoofer or not.

•Each time you press the button, the

subwoofer setting alternates between “YES” and “NO.”

YES : Select this when you have connected a subwoofer. You can adjust the subwoofer output level

(see page 15).

NO : Select this when you have not connected or have disconnected a subwoofer.

12