JVC RX-7000VBK manual Release CATV/DBS Power, Try to operate your Catv converter by pressing

To change the transmittable signals for operating a CATV converter

To change the transmittable signals for operating another manufacturer’s VCR

1.Set the remote control mode to “CATV/DBS.”

2.Press and hold CATV/DBS POWER.

3.Press TV/DBS.

4.Enter manufacturer’s code (two digits) using

buttons 1–9, and 0.

See the list below to find the code.

Examples: For an RCA product, press 1, 9.

For a SONY product, press 2, 0.

1.Set the remote control mode to “AUDIO/TV/ VCR.”

2.Press and hold VCR POWER.

3.Press VCR.

4.Enter manufacturer’s code (two digits) using

buttons 1–9, and 0.

See the list below to find the code.

Examples: For a JVC product, press 0, 1.

For an NEC product, press 2, 5.

5. Release CATV/DBS POWER.

After setting the remote control mode selector to “CATV/DBS,” you can perform the following operations on the CATV convertor :

CATV/DBS POWER Turns on and off the CATV converter.

CHANNEL +/–	Changes the channels.
1 – 10, 0, 100+ (+10)	Selects the channels.
	The 100+ (+10) button will function as
	the ENTER button if your equipment
	requires pressing ENTER after
	selecting a channel number.

Note:

Refer to the manual supplied with your CATV converter.

6. Try to operate your CATV converter by pressing

CATV/DBS POWER.

When your CATV converter turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

CATV converter , try each one until the correct one is entered.

Manufacturer	Codes
ECHOSTAR	21
GI JERROLD	01, 02, 03, 04, 05,
	06, 07, 08
HAMLIN/REGAL	15, 16, 17, 18
PIONEER	13, 14
RCA	19
SCIENTIFIC ATLANTA	09, 10
SONY	20
ZENITH	11, 12

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

5. Release VCR POWER.

The following button can be used for operating the VCR (with the remote control mode selector set to “AUDIO/TV/VCR”):

VCR POWER Turns on and off the VCR.

After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:

CHANNEL +/– Changes the TV channels on the VCR. 1 – 10, 0, 100+ (+10) Selects the TV channels.

	The 100+ (+10) button will function
	as the ENTER button if your VCR
	requires pressing ENTER after
	selecting a channel number.
PLAY	Starts playback.
1	Rewinds a video tape.
`	Fast winds a video tape.
STOP	Stops operation.
PAUSE	Pauses.

ƒREC: Starts recording or enters recording pause.

Notes:

•Refer to the manual supplied with your VCR.

•You can use either VCR button or the VCR CONTROL button to activate the buttons listed above. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.

6.Try to operate your VCR by pressing VCR POWER.

When your VCR turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

VCR, try each one until the correct one is entered.

Manufacturer	Codes	Manufacturer		Codes
JVC	01, 02, 03	PHILIPS	09
EMERSON	11, 26	RCA	05, 06
FISHER	29	SAMSUNG	24
FUNAI	10, 14, 15, 16	SANYO	21, 22, 23
GOLD STAR	12	SHARP	27, 28
HITACHI	04	SHINTOM	30
MITSUBISHI	13	SONY	18, 19, 20
NEC	25	ZENITH	08
PANASONIC	07, 17

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

47