JVC RX-7000VBK manual Operating Video Components, DVD player

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK terminals (see page 41) in addition to the connections using cables with RCA pin plugs (see pages 6 and 7).

•Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR jacks is set to code “A.”

•When using the remote control:

–For the DVD player and VCR operations, aim the remote control directly at the remote sensor on each component, not on the receiver.

–For the TV operations:

7If the TV has the AV COMPU LINK terminal “RECEIVER/ AMP,” aim the remote control directly at the remote sensor on the receiver.

7If the TV has the AV COMPU LINK terminal “AV COMPU LINK EX,” aim the remote control directly at the remote sensor on the TV.

		TV		AUDIO
		VCR		CATV/DBS
DVD	DVD MUILTI	CD		TAPE/MD
TV/DBS		PHONO		FM/AM
VCR		ANALOG/DIGITAL		SLEEP
SURROUND			CENTER
ON/OFF	1	2		3
			MENU
SURROUND	TEST		REAR-L
MODE	4	5		6
			ENTER
CD-DISC	EFFECT		REAR-R
	7/P	8		9
SOUND	SEA MODE	SUBWOOFER
	10	0		+10
	RETURN	FM MODE		100+
					AUDIO/
				AUDIO/	TV/VCR
				TV/VCR
MENU
				CATV/DBS	CATV/DBS
	SET
EXIT				TEXT
				DISPLAY
TV VOL	CHANNEL		VOLUME		Check to see if the remote
					control mode selector is set
					to the correct position.
TV/VIDEO	VCR	TAPE/MD		MUTING	To operate the audio
	CONTROL
					system, TVs, VCRs, and
/REW	PLAY			FF/
DOWN	TUNING			UP	DVD players, set it to
REC	STOP			PAUSE	“AUDIO/TV/VCR.”
RM-SRX7000J REMOTE CONTROL

VCR

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

VCR POWER: Turns on or off the VCR.

After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:

1 – 9, 0: Selects the TV channels on VCR.

PLAY: Starts playing.

1: Rewinds a tape.

`: Fast winds a tape.

STOP: Stops operations.

PAUSE: Pauses playing. To release it, press PLAY.

ƒREC: Press this button with the PLAY button to start

recording.

Press this button with the PAUSE button to enter recording pause.

CHANNEL +/–: Changes the TV channels on the VCR.

Note:

You can use either VCR button or the VCR CONTROL button to activate the buttons listed above. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.

DVD player

After pressing DVD or DVD MULTI (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a DVD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous) track.
¢:	Skips to the beginning of the next track.
STOP:	Stops playing.

PAUSE: Stops playing temporarily. To release it, press PLAY.

After pressing DVD or DVD

MULTI, these buttons can be used			CENTER
		2	3
for the DVD menu operations.
			MENU
	TEST		REAR-L
Note:	4	5	6
			ENTER

For detailed menu operations, refer to the		REAR-R
	8
instructions supplied with the discs or the
DVD player.

TV

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

TV POWER: Turns on or off the TV.

TV VOL +/–: Adjusts the volume.

TV/VIDEO: Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a TV:

CHANNEL +/–: Changes the channels.

1 – 9, 0, 100+: Selects the channels.

RETURN: Alternates between the previously selected channel and the current channel.

45