JVC rx-8010vbk Adjusting the Equalization Patterns, Using the Sleep Timer, Recording a Source

Adjusting the Equalization Patterns

You can adjust equalization to your preference.

• You can do this setting for each source.

Before you start, remember....

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than play all night.

From the remote control ONLY:

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

Press SLEEP repeatedly.

SLEEP

On the front panel:
1. Press DIGITAL EQ (Equalization)
	DIGITAL	LEVE
repeatedly to select the frequency.	EQ	ADJU
• Each time you press the button, the frequency
with its current level changes as follows:

EQ63Hz	EQ250Hz		EQ1kHz
and its level	and its level		and its level
EQ16kHZ		EQ4kHz
and its level		and its level
2. Press CONTROL UP 5/DOWN °				CONTROL

The SLEEP indicator lights up on the display, and the shut-off time changes as follows (in minutes):

10 20 30 40 50 60 70 80 90

0(Canceled)

When the shut-off time comes

The receiver turns off automatically.

To check or change the time remaining until the shut-off time

Press SLEEP once.

The remaining time until the shut-off time appears in minutes.

repeatedly to adjust the frequency level.

DOWN UP

• To change the shut-off time, press SLEEP repeatedly.

The frequency level changes by 2 dB from –8 dB to +8 dB. The DIGITAL EQ indicator lights up on the display.

3. Repeat Steps 1 and 2 to adjust the other frequency level.

To flat the equalization pattern,

Set all the frequency levels to “0” in step 2. The DIGITAL EQ

To cancel the Sleep Timer

Press SLEEP repeatedly until “SLEEP 0min” appears on the display. (The SLEEP indicator goes off.)

• Turning off the power also cancels the Sleep Timer.

Recording a Source

indicator goes off from the display.

From the remote control:

1.Press SOUND.

The 10 keys are activated for sound adjustments.

2.Press DIGITAL EQ (Equalization) repeatedly to select the frequency you want. “EQ” appears on the remote control display window.

SOUND

∗DIGITALEQ

10

RETURN

For analog-to-analog recording

You can record any analog source through the receiver to —

•the cassette deck (or MD recorder) connected to the TAPE/MD jacks,

•the VCRs connected to the VCR 1 and VCR 2 jacks, and

•the CD recorder connected to the CDR jacks

— at the same time.

For digital-to-digital recording

•Each time you press the button, the frequency with its level changes as follows:

EQ63Hz	EQ250Hz		EQ1kHz
and its level	and its level		and its level
EQ16kHZ		EQ4kHz
and its level		and its level
3. Press LEVEL + or − repeatedly to adjust				+		∗BAL L
the frequency level.
The frequency level changes by 2 dB from				CH/∗LEVEL
–8 dB to +8 dB. The DIGITAL EQ indicator					−∗BAL R
lights up on the display.

4.Repeat steps 2 and 3 to adjust the other frequency level.

To flat the equalization pattern,

Set all the frequency levels to “0” in step 3. The DIGITAL EQ indicator goes off from the display.

Notes:

•When the line direct function is turned on, the digital equalization cannot be adjusted.

•The digital equalization affects the front speaker sounds only.

You can record the currently selected digital input source through the receiver to a digital recording device connected to the DIGITAL OUT terminal.

Notes:

•Analog-to-digital and digital-to-analog recordings are not possible.

•The output volume level, midnight mode (see page 13), bass boost (see page 14), digital equalization (see the left), Surround modes and DSP modes (see page 24) cannot affect the recording.

•The test tone signal (see page 27) does not come out through the DIGITAL OUT terminal.

15