Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until | CT SETTING |
“LFE ATT” (Low Frequency |
|
Effect Attenuator) appears on the |
|
display. |
|
The display changes to show the current setting.
To set the DIGITAL 2/3/4 terminals:
1. Press SETTING again until | T | SETTING |
DIGITAL 2/3/4 terminals' setting |
|
|
|
| |
appears on the display. |
|
|
|
| |
The display changes to show the current settings. |
|
|
DIGITAL 2 terminal setting |
|
|
2. Press CONTROL UP 5/DOWN ° CONTROL
DOWN UP
to select the low frequency effect attenuator level.
DIGITAL 3 terminal setting DIGITAL 4 terminal setting
2. Press CONTROL UP 5/DOWN ° CONTROL
• Each time you press the button, the display changes to show the following:
0dB 
10dB
to select the appropriate digital terminal settings.
• Each time you press the buttons, the
DOWN UP
0dB: Normally select this.
10dB: Select this when the bass sound is distorted.
Notes:
•Low frequency effect attenuator is not valid for the DVD MULTI playback mode.
•This function takes effect only when the Dolby Digital or DTS Digital Surround sounds with LFE signal comes in (with “SUBWOOFER” set to “YES”).
Digital Input (DIGITAL IN) Terminal Setting
When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3/4).
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
To set the DIGITAL 1 terminal:
1. Press SETTING repeatedly until |
| CT | SETTING |
“DGTL COAX” (Digital Coaxial) |
| ||
|
|
| |
|
|
| |
appears on the display. |
|
|
|
The display changes to show the current setting |
|
|
|
for DIGITAL 1 terminal. |
|
|
|
2. Press CONTROL UP 5/DOWN ° |
| CONTROL | |
to select the appropriate digital | DOWN UP | ||
|
|
| |
terminal setting. |
|
|
|
•Each time you press the button, the display changes to show the following:
1:DVD Ò1: MD** Ò1: CDR Ò1 : TV (or DBS* ) Ò
1:CD Ò(back to the beginning)
*If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 16).
**Change the source name to “MD” for TAPE/MD jacks when you use an MD recorder (see page 16).
display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to “DVD”
2:CD 3: TV (or DBS* ) 4: CDR Ò
2:CD 3: TV (or DBS* ) 4: MD** Ò
2:CD 3: MD** 4: CDR Ò
2:MD** 3: TV (or DBS* ) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “MD” **
2:CD 3: TV (or DBS*) 4: DVD Ò
2:CD 3: DVD 4: CDR Ò
2:DVD 3: TV (or DBS*) 4: CDR Ò
2:CD 3: TV (or DBS*) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CDR”
2:MD** 3: TV (or DBS*) 4: DVD Ò
2:CD 3: TV (or DBS*) 4: DVD Ò
2:CD 3: TV (or DBS*) 4: MD** Ò
2:CD 3: MD** 4: DVD Ò
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “TV” or “DBS”
2:CD 3: MD** 4: CDR Ò2: MD** 3: DVD 4: CDR Ò
2:CD 3: DVD 4: CDR Ò2: CD 3: DVD 4: MD** Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CD”
2:DVD 3: TV (or DBS*) 4: MD** Ò
2:DVD 3: MD** 4: CDR Ò
2:MD** 3: TV (or DBS*) 4: CDR Ò
2:DVD 3: TV (or DBS*) 4: CDR Ò (back to the beginning)
*If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 16).
**Change the source name to “MD” for TAPE/MD jacks when you use an MD recorder (see page 16).
Note:
When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.
•DIGITAL 1 (coaxial): For DVD player
•DIGITAL 2 (optical): For CD player
•DIGITAL 3 (optical): For digital TV broadcast tuner
•DIGITAL 4 (optical): For CD recorder
19
