Manuals / Brands / Home Audio / Stereo Receiver / JVC / Home Audio / Stereo Receiver

JVC RX-888RBK FM tuner (IHF), AM (MW/LW) tuner, General

1 60

Download 60 pages, 1.39 Mb

56

English

FM tuner (IHF)

Tuning Range: 87.50 MHz to 108.00 MHz

Usable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 ohms)

50 dB Quieting Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 ohms)

Stereo: 41.3 dBf (31.5 µV/75 ohms)

Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf

Stereo: 73 dB at 85 dBf

Total Harmonic Distortion: Monaural: 0.4% at 1 kHz

Stereo: 0.6% at 1 kHz

Stereo Separation at REC OUT: 35 dB at 1 kHz

Alternate Channel Selectivity: 45 dB: (±400 kHz)

Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)

AM (MW/LW) tuner

Tuning Range: MW: 522 kHz to 1,629 kHz

LW: 144 kHz to 288 kHz

Usable Sensitivity: Loop antenna 400 µV/m

Signal-to-Noise Ratio: 50 dB (100 mV/m)

General

Power Requirements: AC 230V , 50 Hz

Power Consumption: 250 watts (at operation)

2 watts (in standby mode)

Dimensions (W x H x D): 435 x 157 x 412.5 mm

(17 3/16 x 6 3/16 x 16 1/4 inches)

Mass: 11.3 kg (25.0 lbs)

Designs & specifications are subject to change without notice.

EN45_56.RX-888R[E]/f 99.4.20, 1:44 PM56

Contents

Main LVT0177-001A RX-888R[E]COVER/f 99.4.20, 1:45 PM1 [E] RX-888RBK VIDEO + 1 BIT P-E-M D-D-COMVERTER /P G-1 G-2 Deutsch Franais Nederlands Italiano Espaol Table of Contents Parts Identification q w e r Getting Started Before Installation General Locations Handling the receiver Connecting the Speakers IMPORTANT: 2 1 3 4 Connecting Audio/Video Components Analog connections Audio component connections Connecting the rear and center speakers + Video component connections A BEF DC A B D E ABC Digital connections Connecting the Power Cord Putting Batteries in the Remote Control 13 2 Basic Operations The following operations are commonly used when you play any sound source. Turning the Power On and Off (Standby) Selecting the Source to Play When playing a digital source through a digital terminal Adjusting the Volume Selecting the Front Speakers Listening only with headphones Muting the Sound From the remote control ONLY: Listening at Low Volume (Loudness) Attenuating the Input Signal Adjusting the Subwoofer Output Level Basic Settings Page Page Page Using the Sleep Timer From the remote control ONLY: 00 2010 30 40 50 60 70 80 90 Storing the Basic Settings and Adjustments One Touch Operation Receiving Radio Broadcasts Using Preset Tuning To store the preset stations 1. Tune in the station you want to preset (see Tuning in Stations Manually). 2. Press TUNER/SEA MEMORY. Page Searching for a Program by PTY Codes To search for a program using the PTY codes 1. Press PTY SEARCH while listening to an FM station. Using the RDS (Radio Data System) to Receive FM Stations What information can RDS signals provide? 3. Press PTY SEARCH again, while the PTY code selected in the previous step is still on the display. 1. Press PTY SEARCH while listening to an FM station. 3. Press PTY SEARCH again, while the PTY code selected in the previous step is still on the display. Switching to a Broadcast Program of Your Choice Temporarily 1. Press EON so that the last selected program type appears on the INFO 2. Press TA/NEWS/INFO until the program type you want appears on the display. TA NEWS/INFO TA/INFO NEWS TA/NEWS/INFO Using the SEA Modes The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds. Selecting Your Favorite SEA Mode To cancel the SEA mode 1. Press SOUND. Using the DSP Modes 3D-PHONIC modes DAP modes Surround modes Dolby Surround (Dolby Digital and Dolby Pro Logic) DTS Digital Surround MPEG Multichannel JVC Theater Surround Available DSP Modes According to the Speaker Arrangement Page Page 5. Press TEST again to stop the test tone. 6. Press CNTR TONE to select the SOFT 2 SOFT 1 2. Adjust the speaker output levels. 3. Adjust the center tone. SHARP 1 SHARP 2FLAT 1. Press SURROUND MODE repeatedly until THEATER or DIG THEATER appears on the 2. Press SOUND. 3. Press TEST to check the speaker output balance. 5. Press TEST again to stop the test tone. 6. Press CNTR TONE to select the 7. Press EFFECT to select an effect level you want. 1. Press DSP MODE repeatedly until THEATER or DIG THEATER appears on the 2. Adjust the speaker output levels. SHARP 1 SHARP 2FLATSOFT 2 SOFT 1 3. Adjust the center tone. 4. Adjust the effect level. 1. Press DSP MODE repeatedly until the mode you want appears on the To cancel the DSP mode 1. Press SURROUND MODE repeatedly until the DSP mode you want appears on the display. To cancel the DSP mode Using the DVD MULTI Playback Mode 4. Adjust the center tone. Activating the DVD MULTI Playback Mode 1. Turn SOURCE SELECTOR until DVD MULTI appears on the 2. Select the analog discrete output mode on the DVD player, and start playing a DVD. 1. Press DVD MULTI so that DVD MULTI appears on the display. 2. Select the analog discrete output mode on the DVD player, and start playing a DVD. If you need to make any adjustment, go to the following steps. 3. Press SOUND. 5. Press CNTR TONE to select the Using the On-Screen Menus EN34_44.RX-888R[E]/f 99.4.20, 1:43 PM34 SET On-Screen Operation buttons (on the remote control) Selecting Different Sources for Picture and Sound (Also see page 10) Page Page Page Page COMPU LINK Remote Control System Remote Control through the Remote Sensor on the Receiver Automatic Source Selection Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 connection Synchronized Recording TEXT COMPU LINK Remote Control System FUNCTIONS: Displaying the Disc Information on the TV screen Disc Search: Only for CD Player Disc Title Input OPERATIONS Showing the Disc Information on the TV Screen Press TEXT DISPLAY while CD or MD is selected as the source. Page Page Page Operating JVCs Audio/Video Components Sound control section (Amplifier) CD player CD player-changer Tuner Turntable Cassette deck MD recorder VCR DVD player Operating Other Manufacturers Video Equipment To change the transmittable signals for operating another manufacturers TV 5. Release TV/CATV/DBS . 6. Try to operate your TV by pressing TV/CATV/ DBS . Page Page Page Page Page Page Troubleshooting PROBLEM SOLUTION POSSIBLE CAUSE Specifications Amplifier FM tuner (IHF) AM (MW/LW) tuner General