JVC SR-DVM70US Manual Timer Programming, 48 EN TIMER RECORDING ON HDD/DVD DECK, FGDE, FGDE, NOTES:, Relief Recording, Cable box and DBS Receiver Users

48 EN TIMER RECORDING ON HDD/DVD DECK

Manual Timer Programming		8 Press FGto select ASOURCEB, then press ENTER. Press FG
		to select the desired source.
You can program this unit to timer record as many as 16 programs.		9 Press FG to select ACHB, then press ENTER. Press FG to
		select the desired channel.
If you do not know the PlusCode number for the program you wish
		10 Press FG to select ACONFIRMB, then press ENTER.
to record, use the following procedure to set your unit to
timer record the program.		11 Set the other recording options as required.
● Make sure that the unit’s built-in clock is set properly.		● Refer to step 8 in AVCR Plus+ Timer ProgrammingB
		(A pg. 46).
● Turn on the unit.		12 Press FG to select AOKB,
● Turn on the TV and select the AV mode.				2 PROGRAM > CALENDAR PR. (3/3)
● Slide the TV/CABLE/DBS/DVD switch to DVD.		then press ENTER to access		01/08/03 WED 10:30PM - 11:00PM		DBS 100
		the Program Confirmation
				GARDENING	[EDUCATION] FR360
					1:00	28:00
		screen.	SELECT WITH @ INPUT NAME		GARDENING
		13 Press DE to select AEXITB,	THEN PRESS [ENTER]
CABLE/DBS				CATEGORY	EDUCATION
			PRESS [PROG] TO EXIT
				WEEKLY/DAILY	MON-FRI (FOR A WEEK)
TV	DVD	then press ENTER to		REC MODE	FR360
		complete timer	PROG	ENTER
				OK
		programming.
			EXIT	SELECT

● To program another timer,

press DE to select ACONTINUEB, then press ENTER.

● If APROGRAM OVERLAPPEDB appears on the TV screen, delete or modify the programs.

PROG

ENTER

FGDE

1Load a recordable disc if recording to DVD.

2Press PROG to access the program top screen.

3Press FGDE to select ACALENDAR PR.B, then press ENTER.

●When APROGRAM FULL DELETE UNWANTED TIMER PROGRAMSB appears on the TV screen, you need to cancel some of the reserved programs. (A pg. 49)

4Press FGDE to select the desired date, then press ENTER.

5Press FGto select ARECORD

TOB, then press ENTER. Press			2 PROGRAM > CALENDAR PR. (2/3)
FG to select the desired			01/08/03 WED 10:30PM - 11:00PM DBS 100
						[MISC. ] XP
recording deck, then press
	SELECT WITH @		RECORD TO		HDD
ENTER.	THEN PRESS [ENTER]
			START		10:30PM
	PRESS [PROG] TO EXIT
6 Press FG to select ASTARTB,			STOP		11:00PM
			SOURCE		CATV
then press ENTER. Press FG			CH		100
	PROG	ENTER
to set the desired start time,				CONFIRM
	EXIT	SELECT

then press ENTER.

●Each press of FG increases/decreases the start time in 1- minute interval.

●To increase/decrease the start time in 30-minutes interval, press and hold FG.

NOTES:

●When two successive programs are recorded on a DVD-RW disc with Manual Timer Programming function, the beginning of the second one may be left off the recording.

●If the copy limited program is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

Cable box and DBS Receiver Users

To timer record a satellite broadcast using Manual Timer Programming:

APerform AManual Timer ProgrammingB (A pg. 48).

BSet the cable box or DBS receiver to the appropriate channel before the selected program begins.

CLeave the cable box or DBS receiver’s power on.

Relief Recording

When a program that is set for the DVD deck cannot be recorded properly, the program is recorded to the HDD deck instead in XP mode.

●If the remaining capacity of the hard disc is not sufficient, the program is recorded to the DVD deck until the remaining capacity of the DVD disc lasts.

●If AJUSTB is selected for the recording mode, the current recording mode for the DVD deck is applied.

7Press FG to select ASTOPB, then press ENTER. Press FG to set the desired stop time, then press ENTER.

●Each press of FG increases/decreases the stop time in 1- minute interval.

●To increase/decrease the stop time in 30-minutes interval, press and hold FG.