—24—
Page 24 December 26, 2003 2:23 pm
Insert Editing and AV Dubbing
Insert Editing:
You can replace a recorded scene with new scene recorded on
another tape or with other material. Both the picture and the sound
recorded on the Hi-Fi sound track are replaced at the same time.
AV Dubbing:
You can perform Audio Dubbing and Insert Editing at the same
time. This means that the picture and the sounds recorded on the
Hi-Fi sound track and on the normal track are replaced at the
same time.
●For AV Dubbing, you can edit pictures and sound using different
sources; connect a video source to the video input connector,
and an audio source to the audio input connectors.
AMake connections
Connect an audio/video cable between the VCR’s audio/video
input connectors and the other component’s audio/video output
connectors.
●Insert Editing and AV Dubbing are possible by using the audio/
video input connectors on the front panel or on the rear panel.
BSelect input mode
Select “F-1” —when connecting the other component to the
audio/video input connectors on the front panel.
Select “L-1”— when connecting the other component to the
audio/video input connectors on the rear panel.
Press AUX or CH+/– on the Remote. Or push the JOG dial, then
turn it to the left or right.
CSelect video input connector
Select the appropriate mode depending on the connector being
used (墌pg.19).
When using S-VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “S-VIDEO”.
When using S-VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “S-VIDEO”.
When using VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “VIDEO”.
When using VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “VIDEO”.
DSelect edit mode
Set the edit mode to “ON” for the VCRs if such a mode is
equipped.
●On this VCR, set “PICTURE CONTROL” to “EDIT” (墌pg.18).
ELocate end point
ALoad the cassette to be edited into the VCR and press
PLAY
(
4
).
BPress PAUSE (9) when you find the end of the scene for which
you want to edit.
CPress C.RESET so that the counter reading becomes “0:00:00”.
FLocate start point, and engage Insert Editing mode
Press REW (3), then press PAUSE (9) when you find the
beginning of the scene for which you want to edit, then press
INSERT.
●The VCR enters the Insert Editing Pause mode. “䡬” and “$”
light on the display panel.
●If you want to perform AV Dubbing and replace the picture,
Hi-Fi audio soundtrack and normal audio soundtrack all at the
same time, press INSERT, then press A.DUB also.
GStart editing
Load the source cassette and engage the Play mode of the other
component, then press PLAY (4) on the VCR. Insert Editing begins
at this point.
●Insert Editing stops automatically when the counter reaches
“0:00:00”, and the VCR enters the Play mode.

To stop editing any time during recording

Press STOP (8) on the Remote or STOP/EJECT (0) on the
VCR, then engage the Stop mode of the other component.
NOTES:
●Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish editing (墌pg. 18).
●Editing is not possible with a cassette whose record safety tab
has been removed. If you want to record onto a tape with its
record safety tab removed, set “REC SAFETY” to “OFF”
(墌pg.19).
●The recording speed (SP/EP) is determined by the previous
recording to be replaced. If the recording speed changes on the
tape to be edited while editing the tape, the inserted picture will
be distorted where the recording speed changes.
●When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.
●DAY/TIME INSERT (墌pg.19) is not available during Insert
Editing.
Source tape
Edited tape
Before
editing
After
editing
Normal track
Video and Hi-Fi track
Source tape
Edited tape
Before
editing
After
editing
To S-video output
This VCR (for recording)
Another VCR (for playback)
S-video cable
(supplied)
To S-VIDEO IN
To audio/video output
Audio/video cable
(supplied)
To AUDIO/VIDEO IN
SR-V101US.fm Page 24 Friday, December 26, 2003 2:24 PM