Manuals / JVC / Photography / Digital Camera

JVC TK-C676 Duplex, Four wires must be connected, For example connection with an RM-P2580 Camera

Models: TK-C676

1 44

Download 44 pages 37.37 Kb

Page 11

Image 11

Use twisted-pair cables for the connections.

●Duplex

When the camera is controlled using the full duplex proto- col, set Switch 5 to OFF.

Camera	Controller
RX+	TX+
RX–	TX–
TX+	RX+
TX–	RX–

Four wires must be connected.

For example (connection with an RM-P2580)

Camera		RM-P2580
RX+ C		C TX+
RX–	D	D TX–
TX+ A		A RX+
TX–	B	B RX–

●Simplex

When the camera is controlled using the simplex trans- mission protocol, set Switch 5 to ON.

Camera	Controller
RX+	TX+
RX–	TX–

Two wires must be connected.

Page 11

Image 11

JVC TK-C676 manual Duplex, Four wires must be connected, For example connection with an RM-P2580 Camera, Simplex

Contents

TK-C676 Important Safeguards Contents Instructions Ceiling mount FeaturesProvided Accessories Safety Precautions Zooming Precautions for Correct Operation Preset positions Camera setups with which auto focusing may be difficult Ceiling Mount Controls, Connectors and IndicatorsConnector Male Camera Connector Female$ Machine ID Switch Setting SwitchesCable connections P Switch settings PObserve the following points when connecting compo Multi-Drop Communication SystemMemo Terminal side of the Ceiling Mount Switch 7 OFF Switch 8 onPoint-to-Point Communication System For example connection with an RM-P2580 Camera Four wires must be connectedTwo wires must be connected Duplex Setting switches Switch SettingsExample Camera ID check procedureMachine ID Bers on the RM-P2580Remove the cover from the Ceiling Mount Cable ConnectionsMake a 90 mm diameter hole in the ceiling Connect the cablesAttach the cover Attaching the Camera Attaching a safety wireAttach the drop prevention wire Attaching the Ceiling MountTighten the lock screw Ensure that the lock screw is looseFit the camera Rotate the cameraPress the SET button Setup ProcedureSetting the camera menus from an RM-P2580 Press and hold the Menu button for 3 secondsNormal screen Menu for setting up the home posi- tion onlyMenu for setting up the function of each preset position Menu Screen FlowCamera Function Screen Camera TITLE/ALARM Screen Alarm OUT1 Alarm Input PolarityAlarm Alarm OutputCamera ALC/ExDR screen Camera Video Adjustment ScreenSense UP AGC ModeExDR Mode 10 dBLOW ColourMode LevelDemonstration Alarm DisplayHome Motion Detect Screen Area EditAuto PAN/PATROL/TRACE Screen Position Function SET Screen Factory Settings screenPrivate Mask Setup Repeat steps 5 and 6 for each title character Camera Title SetupPress the Tele button Repeat steps 5 to 7 for each area title Area Title SetupMove the cursor to Area Title Edit and press the SET button Press the FAR buttonRepeat steps 5 to 7 for each alarm title Alarm Title SetupDisplay the Setup menu on the camera Area Edit screen Home Motion Detect SetupMove the cursor to Area Edit and press the SET button Home Motion Detect menuAdjust the viewing angle of the start position Auto PAN SetupSet the auto pan mode and speed Auto Patrol Setup Auto Trace SET screen is displayed Auto Trace SetupMove the cursor to Autotrace SET and press the SET button Set the patrol start positionPosition Title screen Position Title SetupRepeat steps 5 to 7 for each title character Position Function SET screenCeiling plate Attaching a Ceiling Flush Mount Bracket Optional WB-S575Clamp the Ceiling Flush Mount Bracket Connection Cables Attach the Ceiling Mount to the Ceiling Flush Mount BracketAttach the ceiling panel Check the release labels thoroughly before removal Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the ceiling panel Remove the cameraTurned on TroubleshootingSymptom Cause Information Remedy Power cannot beGeneral SpecificationsCamera Pan/Tilt MechanismWB-S575 Ceiling flush mount bracket + Ceiling panel External dimensions Unit mmDimensions in combination with the WB-S575 Ceiling mount holeTK-C676 Dome Type Camera