Manuals / JVC / Photography / Digital Camera

JVC TK-C676 manual Memo

Models: TK-C676

1 44

Download 44 pages 37.37 Kb

Page 9

A system that does not employ the RM-P2580 as the controller

MEMO

Be sure to terminate the control signal cable at both ends. The cables (length of stub) connecting pieces of non-terminated equipment (cameras or controllers) must be as short as possible. If the length of stub is too long, control precision may suffer.

●When the controller is not located at the end of a system.

(An AC 24V power source must be supplied to each camera)

CAM1

	CONTROL Cable
CAM2 Length of stub	CAM31 Length of stub CAM32
	Length of stub

PROTOCOL(1)	: ON
MACHINE ID	: 01
RX TERM	: ON

PROTOCOL(1)	: ON
MACHINE ID	: 02
RX TERM	: OFF

CONTROLLER*

PROTOCOL(1)	: ON
MACHINE ID	: 31
RX TERM	: OFF

PROTOCOL(1)	: ON
MACHINE ID	: 32
RX TERM	: ON

•Set the TERM switches of the cameras at each end (CAM1 and CAM32) to ON, and the TERM switches of the other cameras to OFF.

•Do not terminate at the controller.

VIDEO SWITCHER, etc.

●When the controller is located at the end of a system.

(An AC 24V power source must be supplied to each camera)

CONTROL Cable

CAM1

PROTOCOL(1)	: ON
MACHINE ID	: 01
RX TERM	: ON

	CAM2 Length of stub	CAM32	Length of stub	Terminate it
				with 110	Ω.

			CONTROLLER*
PROTOCOL(1) : ON		PROTOCOL(1) : ON
MACHINE ID	: 02	MACHINE ID	: 32
RX TERM	: OFF	RX TERM	: OFF

•Set the TERM switch of CAM1 to ON, and terminate at the con- troller with a resistance of 110 Ω.

Set the TERM switches of the other cameras to OFF.

VIDEO SWITCHER, etc.

9

Image 9

JVC TK-C676 manual Memo

Contents

TK-C676 Important Safeguards Contents Provided Accessories FeaturesSafety Precautions Instructions Ceiling mount Preset positions Precautions for Correct OperationCamera setups with which auto focusing may be difficult Zooming Ceiling Mount Controls, Connectors and Indicators$ Machine ID Switch Camera Connector FemaleSetting Switches Connector MaleObserve the following points when connecting compo Switch settings PMulti-Drop Communication System Cable connections PMemo Switch 7 OFF Switch 8 on Point-to-Point Communication SystemTerminal side of the Ceiling Mount Two wires must be connected Four wires must be connectedDuplex For example connection with an RM-P2580 Camera Setting switches Switch SettingsMachine ID Camera ID check procedureBers on the RM-P2580 ExampleMake a 90 mm diameter hole in the ceiling Cable ConnectionsConnect the cables Remove the cover from the Ceiling MountAttach the cover Attach the drop prevention wire Attaching a safety wireAttaching the Ceiling Mount Attaching the CameraFit the camera Ensure that the lock screw is looseRotate the camera Tighten the lock screwSetting the camera menus from an RM-P2580 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET buttonMenu for setting up the function of each preset position Menu for setting up the home posi- tion onlyMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Alarm Alarm Input PolarityAlarm Output Alarm OUT1Camera ALC/ExDR screen Camera Video Adjustment ScreenExDR Mode AGC Mode10 dB Sense UPMode ColourLevel LOWHome Motion Detect Screen Alarm DisplayArea Edit DemonstrationAuto PAN/PATROL/TRACE Screen Position Function SET Screen Factory Settings screenPrivate Mask Setup Camera Title Setup Press the Tele buttonRepeat steps 5 and 6 for each title character Move the cursor to Area Title Edit and press the SET button Area Title SetupPress the FAR button Repeat steps 5 to 7 for each area titleAlarm Title Setup Display the Setup menu on the cameraRepeat steps 5 to 7 for each alarm title Move the cursor to Area Edit and press the SET button Home Motion Detect SetupHome Motion Detect menu Area Edit screenAuto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Move the cursor to Autotrace SET and press the SET button Auto Trace SetupSet the patrol start position Auto Trace SET screen is displayedRepeat steps 5 to 7 for each title character Position Title SetupPosition Function SET screen Position Title screenAttaching a Ceiling Flush Mount Bracket Optional WB-S575 Clamp the Ceiling Flush Mount BracketCeiling plate Attach the Ceiling Mount to the Ceiling Flush Mount Bracket Attach the ceiling panelConnection Cables Remove the ceiling panel Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the camera Check the release labels thoroughly before removalSymptom Cause Information Remedy TroubleshootingPower cannot be Turned onCamera SpecificationsPan/Tilt Mechanism GeneralDimensions in combination with the WB-S575 External dimensions Unit mmCeiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C676 Dome Type Camera