JVC UX-T550 PLAYING CDs, Playing an entire CD, Operate in the order shown, Skip play

PLAYING CDs

Playing an entire CD

The following example of playing an entire CD assumes a CD with 12 tracks and a total playing time of 48 minutes 57 seconds.

Operate in the order shown

		COMPACT		Ù
		DIGITAL AUDIO
ACTIVE HYPER	TIMER/SNOOZE
BASS PRO
				OPEN
CLOCK			LTI J	OG
			MU
ONE TOUCH		BAND
REC
	TAPE	TUNER	CD

!~

STANDBY

VOLUME

AUX Ú

MICRO COMPONENT SYSTEM UX-T550

A U T O T A P E S E L E C T O R

AUTO REVERSE

~Press to open the CD holder.

ÙLoad a CD with the label side facing up and close the CD holder. ! Press to start play. (The power is switched on.)

Ú Adjust.

●As tracks are played, their track numbers go out one by one.

●8-cm (3") CDs can be used in this unit without an adapter.

●To stop in the middle of a CD

During play, press the stop/clear (7) button to stop play.

1 2 3 4 5 6 7 8 9 10 11 12

Notes:

●The following indication may appear when a CD is dirty or scratched, or when the CD is loaded upside down.

In such a case, check the CD and insert again after cleaning the CD or turning it over.

●The total number of tracks and total playback time are displayed.

●To stop a CD temporarily

Press the #8button to stop play temporarily and the playing time display blinks.

When pressed again, play resumes from the point where it was paused.

Caution:

●To change CDs, press the stop/clear (7) button; check that the CD has stopped rotating completely before unloading it.

Skip play

●During play, it is possible to skip forward to the beginning of the next track or back to the beginning of the track being played or the previ- ous track; when the beginning of the required track has been located, play starts automatically.

To listen to the next track...

Press the ¢ button once to skip to the beginning of the next track.

To listen to the previous track...

Press the 4button to skip to the beginning of the track being played. Press twice quickly to skip to the beginning of the previous track.

●By using the MULTI JOG dial, the beginning of tracks can be searched and played.

ULTI JO	G
M

or

Search play (to locate the required position on the CD)

●The required position can be located using fast-forward or reverse search while playing a CD.

Keep pressing for fast-forward search.

Keep pressing for fast-reverse search.

●Hold down the button; search play starts slowly and then gradually increases in speed.

●Since low-volume sound (at about one quarter of the normal level) can be heard in the search mode, monitor the sound and release the button when the required position is located.

●Do not use the unit at excessively high or low temperatures. The recommended temperature range is from 5°C (41°F) to 35°C (95°F).

●After play, unload the CD.

●If mistracking occurs during play, lower the volume.

Direct access play (using the remote control unit)

●Pressing any of the track number buttons will start play from the be- ginning of the designated track. (This function cannot be used during programmed play.)

1 2 3

4 5 6 SLEEP

Ù

7 8 9 DISPLAY

AUTO STEREO

10+10 PRESET AUTO/MONO

TAPE	TUNER	C D
AUX	BAND	~
REVERSE
MODE
REW	MULTI CONTROL FF
BEAT CUT PROGRAM	RANDOM	REPEAT

~Press the CD 3/8 button to set to the CD mode.

ÙDesignate the required track using the track number buttons.

●To designate track numbers 1 to 10, press the track number but- ton corresponding to the track number.

●To designate track number 11 or higher, press the +10 button the required number of times, then a track number button. (Example:

To designate the 20th track, press the +10 button once, then press track number button 10.)

*+10 button:

Each time this button is pressed, the number increases by 10. First press this button to set the 10's digit, then press the track number button to set the 1's digit.

●To skip to another track during play

When the required track number button is pressed, the display shows the designated track number and play starts from the beginning of the designated track.

8