JVC UX-T550 Radio Reception, Stereo AUTO/MONO button using the remote control unit, Preset tuning

RADIO RECEPTION

Operate in the order shown

STEREO AUTO/MONO button

STANDBY

VOLUME

1 2 3

ACTIVE HYPER	TIMER/SNOOZE
BASS PRO

!	AUX	Ú	4	5	6	SLEEP
			7	8	9	DISPLAY

OPEN

CLOCK

ONE TOUCH	BAND
REC
TAPE	TUNER	CD

MULTI

J
OG			AUTO	STEREO
MICRO COMPONENT SYSTEM UX-T550	10	+10	PRESET	AUTO/MONO
	AUX	TAPE	TUNER	C D
			BAND
A U T O T A P E S E L E C T O R	REVERSE
	MODE
		REW	MULTI CONTROL FF

~	Ù	BEAT CUT PROGRAM RANDOM REPEAT
~ Press the TUNER/BAND button.		Ù Select the band.
● The power is switched on and a band and radio frequency will be		! Tune to the required station.
shown in the display.		Ú Adjust.

STEREO AUTO/MONO button (using the remote control unit)

Auto mode:

Set to this position when listening to or recording an FM stereo broad- cast. The STEREO indicator lights when the FM stereo broadcast is received.

MONO:

Set to this position when FM stereo reception is noisy.

When another station is tuned to in the MONO mode, the unit automati- cally enters Auto mode.

Seek tuning

Press the 4 or ¢button for one second or more. The unit enters the seek tuning mode to tune in the nearest station automatically, so the broadcast can be heard. In AM operation, the frequency moves continuously from the MW to the LW band and vice versa.

Manual tuning

Each time the 4 or ¢ button is pressed, the unit steps through the current frequency band. Tuning is done in steps of 50 kHz for FM and 9 kHz for AM (MW/LW).

In AM operation, the tuned frequency moves continuously from the MW (522–1,629 kHz) to the LW (144–288 kHz) band and vice versa.

Press to move to higher frequency.

Press to move to lower frequencies.

Presetting stations (using the remote control unit)

30 stations in FM band and 15 stations in AM (MW/LW) band can be preset as follows:

●Example: (Presetting an FM station broadcasting on 103.5 MHz to preset button “15”)

	1	2	3
	4	5	6	SLEEP
Ú	7	8	9	DISPLAY
	10	+10	AUTO	STEREO	~
			PRESET	AUTO/MONO
	AUX	TAPE	TUNER	C D
			BAND		Ù

REVERSE

MODE

!REW MULTI CONTROL FF

~Press the TUNER/BAND button.

ÙSelect the FM band using the TUNER/BAND button. ! Tune to the required station.

Ú Press preset button “+10”, then “5” for more than 2 sec.

(When “15” blinks in the preset station display, the station has been stored.)

Notes:

●When seek tuning to the required station is not possible because the broadcast signal is too weak, press the 4or ¢button momentar- ily to perform manual tuning.

●When the power is set to STANDBY, or another mode (TAPE, CD or AUX) is selected, the last tuned frequency is stored in memory. When the power is switched on again and TUNER/BAND button is pressed, the same station will be tuned to.

Auto preset tuning (using the remote control unit)

This function scans the current band, detecting frequencies used to broadcast signals, and stores the first 30 FM frequencies and 15 AM (MW/LW) frequencies in memory automatically.

●Press the AUTO PRESET button for more than 2 seconds. The fre- quencies of stations broadcasting signals can be stored in memory automatically in the order of increasing frequency. (30 stations in FM band and 15 stations in AM (MW/LW) band.)

AUTO

PRESET

●Repeat the above procedure for each of the other stations, using a different preset button each time.

●Repeat the above procedure for the other band.

●To change preset stations

Perform step Ú above after tuning to the required station.

Notes:

●The previous stored station is erased when a new station is stored, because the new station’s frequency replaces the previous frequency in memory.

●When listening to an AM (MW/LW) broadcast, noise may be heard if the remote control unit is used.

●All preset stations will be erased when the power cord is discon- nected or a power failure occurs for more than 24 hours. In such cases, store the stations again.

Press for more than 2 seconds.

Using the antennas (see page 2)

FM:Connect the provided FM wire antenna.

AM (MW/LW): Adjust the position of AM (MW/LW) loop antenna.

Preset tuning

●The stations must be preset before this operation can be performed.

(Using the main unit)

1Press the TUNER/BAND button.

2Select the band using the TUNER/BAND button.

3To select the requied preset station, turn the MULTI JOG dial.

ULTI JO	G
M
Down	Up

(Using the remote control unit)

1Press the TUNER/BAND button.

2Select the band using the TUNER/BAND button.

3Press the required preset station buttons (No. 1 – No. 10 and +10). ● The preset station number and frequency corresponding to the but-

ton pressed are shown.

11