![](/images/new-backgrounds/1263739/263739105x1.webp)
Operation Help
1.Set up your Kanguru iNAS 100:
Select the Kanguru iNAS 100 that you want to configure, and then click on the Configure button. An authentication window asking you to enter the administrator’s password appears as shown below:
Click on OK after entering the password. If the name and password are correct, the configuration window is displayed on the screen:
| Setup the name, date and |
| Use DHCP protocol to obtain the WAN IP |
| Use a fixed IP address for | |||||||||
| time of this Disk |
| address automatically. DHCP protocol is |
| WAN port. You will need to | |||||||||
| Server. You can input any |
| commonly used in cable broadband service |
| enter the IP address, subnet | |||||||||
| name you want except |
| or intranet. |
|
| mask and the gateway IP | ||||||||
| special characters. |
|
|
|
|
|
|
| address. | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Change the LAN IP |
|
|
|
|
|
|
|
|
|
|
|
|
| |
address settings of |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |||
your Disk |
|
|
|
|
|
|
|
|
|
|
|
| If PPPoE is used to | |
|
|
|
|
|
|
|
|
|
|
| ||||
Server. If you are not |
|
|
|
|
|
|
|
|
|
|
|
| connect to the | |
familiar with these |
|
|
|
|
|
|
|
|
|
|
|
| Internet, enter the user | |
settings, please keep |
|
|
|
|
|
|
|
|
|
|
|
| name and password | |
them unchanged. |
|
|
|
|
|
|
|
|
|
|
|
| provided by your ISP. | |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| If PPTP is used to |
|
|
|
|
|
|
|
|
|
|
|
|
|
| connect to the |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Internet, enter the |
Configure the DHCP |
|
|
|
|
|
|
|
|
|
|
|
| PPTP server IP | |
service to assign the |
|
|
|
|
|
|
|
|
|
|
|
| Address, user name | |
dynamic IP addresses |
|
|
|
|
|
|
|
|
|
|
|
| and password from | |
for your local |
|
|
|
|
|
|
|
|
|
|
|
| the ISP or network | |
network. |
|
|
|
|
|
|
|
|
|
|
|
| administrator | |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When finished, click on “OK” to |
|
|
| Click “Cancel” to exit and discard |
|
| |||||
|
|
| confirm and exit. |
|
|
|
| changes. |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Change the settings and click on OK when done to complete the configuration setup.
Note:
1.After changing some settings, you may be asked to restart the Kanguru iNAS 100 .
2.If you want to set up detailed configuration, you need to enter the administration web page of the Kanguru iNAS 100 via the browser.
53