This water heater must not be installed directly on carpeting. Carpeting must be protected by metal or wood panel beneath the appliance extending beyond the full width and depth of the appliance by at least 3 inches (76.2 mm) in any direction, or if the appliance is installed in an alcove or closet, the entire floor must be covered by the panel. Failure to heed this warning may result in a fire hazard.

Minimum clearances between the water heater and combustible construction are 0 inch at the sides and rear, 4 inches (102 mm) at the front, and 6 inches (153 mm) from the vent pipe, see Figure 8. Clearance from the top of the jacket is 12 inches (305 mm) on most models. Note that a lesser dimension may be allowed on some models, refer to the label attached adjacent to the gas control valve on the water heater.

FIGURE 8.

A gas water heater cannot operate properly without the correct amount of air for combustion, see Figure 9. Do not install in a confined area such as a closet, unless you provide air as shown in the Combustion Air and Ventilation for Appliances Located in Confined Spaces section. Never obstruct the flow of ventilation air. If you have any doubts or questions at all, call your gas supplier. Failure to provide the proper amount of combustion air can result in a fire or explosion and cause death, serious bodily injury, or property damage.

FIGURE 9.

If this water heater will be used in beauty shops, barber shops, cleaning establishments, or self-service laundries with dry cleaning equipment, it is imperative that the water heater or water heaters be installed so that combustion and ventilation air be taken from outside these areas.

Propellants of aerosol sprays and volatile compounds, (cleaners, chlorine based chemicals, refrigerants, etc.) in addition to being highly flammable in many cases, will also change to corrosive hydrochloric acid when exposed to the combustion products of the water heater. The results can be hazardous, and also cause product failure.

Insulation Blankets

Insulation blankets available to the general public for external use on gas water heaters are not necessary with Kenmore products. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters. Your Kenmore water heater meets or exceeds the EPACT standards with respect to insulation and standby loss requirements, making an insulation blanket unnecessary.

WARNING

Should you choose to apply an insulation blanket to this heater, you should follow these instructions (See Figure 1 for identification of components mentioned below). Failure to follow these instructions can restrict the air flow required for proper combustion, potentially resulting in fire, asphyxiation, serious personal injury or death.

•Do not apply insulation to the top of the water heater, as this will interfere with safe operation of the draft hood.

•Do not cover the outer door, thermostat or temperature & pressure relief valve.

•Do not allow insulation to come within 2” (50.8 mm) of the floor to prevent blockage of combustion air flow to the burner.

10

Page 9 Page 11
Page 10
Image 10
Kenmore 153.338003, 153.338073 owner manual Insulation Blankets
Page 9 Page 11

153.338003, 153.338073 specifications

The Kenmore 153.338003 and 153.338073 are highly regarded models in the realm of home appliances, particularly known for their innovative features and reliable performance. Designed to cater to the evolving needs of modern households, these appliances seamlessly blend functionality with practicality.

Both models are equipped with advanced technology that enhances their efficiency and user-friendliness. The Kenmore 153.338003 and 153.338073 are designed with a focus on energy efficiency, utilizing cutting-edge materials and designs to minimize power consumption while maximizing performance. This not only helps households save on energy bills but also contributes to a more sustainable environment, making these models a responsible choice for eco-conscious consumers.

Key features of these models include a robust heating system and adjustable temperature controls that cater to various cooking needs. Users can easily set their desired temperature, ensuring that the appliance can handle a wide range of tasks, from baking to broiling. The inclusion of multiple cooking settings allows for versatile meal preparations, making it easy to tackle everything from quick snacks to elaborate dinners.

Another standout characteristic is the spacious interior, which provides ample room for cooking larger dishes. The layout is thoughtfully designed to maximize space while ensuring that heat distribution is even across all cooking surfaces. This ensures that meals are cooked thoroughly and uniformly, eliminating the common issue of uneven cooking.

Cleaning and maintenance have also been prioritized in these models. The exterior surfaces are crafted from durable, easy-to-clean materials, while the interior features non-stick coatings that facilitate hassle-free cleaning. Additionally, features such as removable trays and racks allow for simplified upkeep, ensuring that the appliance remains in top condition over time.

User-friendly interfaces are another highlight, with intuitive controls that allow users of all skill levels to operate these appliances with ease. Digital displays provide clear information on cooking times and settings, enhancing the overall cooking experience.

In summary, the Kenmore 153.338003 and 153.338073 stand out in the market due to their effective features, advanced technologies, and practical characteristics. They represent a blend of innovation and convenience, making them an excellent addition to any modern kitchen.
Top Page Image Contents