Venting

VENT DAMPERS - Any vent damper, whether it is operated thermally or otherwise must be removed if its use inhibits proper drafting of the water heater.

Thermally Operated Vent Dampers: This gas-fired water heater has a thermal efficiency at or above 80% which may produce a relatively low flue gas temperature. Such temperatures may not be high enough to properly open thermally operated vent dampers. This would cause spillage of the flue gases and may cause carbon monoxide poisoning.

Vent dampers must bear evidence of certification as complying with the current edition of the American National Standard ANSI Z21.66/CGA 6.14, cover electrically and mechanically actuated vent dampers). Before installation of any vent damper, consult your local Sears Service Center or the local gas supplier for further information.

To insure proper venting of this gas-fired water heater, the correct vent pipe diameter must be utilized. Any additions or deletions of other gas appliances on a common vent with this water heater may adversely affect the operation of the water heater. Consult your gas supplier if any such changes are planned.

For proper venting in certain installations, a larger diameter vent pipe may be necessary. Consult your local Sears Service Center or gas supplier to aid you in determining the proper venting for your water heater from the vent tables in the current edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54.

Periodically check the venting system for signs of obstruction or deterioration and replace if needed.

The combustion and ventilation air flow must not be obstructed.

The water heater with draft hood installed must be connected to a chimney or listed vent pipe system, which terminates to the outdoors. Never operate the water heater unless it is vented to the outdoors and has adequate air supply to avoid risks of improper operation, explosion or asphyxiation.

•For proper draft hood attachment, the draft hood legs may be angled slightly inward.

•Place the draft hood legs in the receiving holes on the top of the water heater. The legs will snap in the holes to give a tight fit. Secure the legs of the draft hood with the supplied draft hood brackets.

•Place the vent pipe over the draft hood. With the vent pipe in position, drill a small hole through both the vent pipe and draft hood. Secure them together with a sheet metal screw, see Figure 17.

FIGURE 17.

Obstructed or deteriorated vent systems may present serious health risk or asphyxiation.

The vent pipe from the water heater must be no less than the diameter of the draft hood outlet on the water heater and must slope upward at least 1/4 inch per linear foot (21 mm per meter), see Figure 18.

FIGURE 18.

All vent gases must be completely vented to the outdoors of the structure (dwelling). Install only the draft hood provided with the new water heater and no other draft hood.

Vent pipes must be secured at each joint with sheet metal screws.

There must be a minimum of 6 inches (153 mm) clearance between single wall vent pipe and any combustible material. Fill and seal any clearance between single wall vent pipe and combustible material with mortar mix, cement, or other noncombustible substance. For other than single wall, follow vent pipe manufacturer’s clearance specifications. To insure a tight fit of the vent pipe in a brick chimney, seal around the vent pipe with mortar mix cement.

Failure to have required clearances between vent piping and combustible material will result in a fire hazard.

Be sure vent pipe is properly connected to prevent escape of dangerous flue gases which could cause deadly asphyxiation.

15

Page 14 Page 16
Page 15
Image 15
Kenmore 153.338073, 153.338003 owner manual Venting
Page 14 Page 16

153.338003, 153.338073 specifications

The Kenmore 153.338003 and 153.338073 are highly regarded models in the realm of home appliances, particularly known for their innovative features and reliable performance. Designed to cater to the evolving needs of modern households, these appliances seamlessly blend functionality with practicality.

Both models are equipped with advanced technology that enhances their efficiency and user-friendliness. The Kenmore 153.338003 and 153.338073 are designed with a focus on energy efficiency, utilizing cutting-edge materials and designs to minimize power consumption while maximizing performance. This not only helps households save on energy bills but also contributes to a more sustainable environment, making these models a responsible choice for eco-conscious consumers.

Key features of these models include a robust heating system and adjustable temperature controls that cater to various cooking needs. Users can easily set their desired temperature, ensuring that the appliance can handle a wide range of tasks, from baking to broiling. The inclusion of multiple cooking settings allows for versatile meal preparations, making it easy to tackle everything from quick snacks to elaborate dinners.

Another standout characteristic is the spacious interior, which provides ample room for cooking larger dishes. The layout is thoughtfully designed to maximize space while ensuring that heat distribution is even across all cooking surfaces. This ensures that meals are cooked thoroughly and uniformly, eliminating the common issue of uneven cooking.

Cleaning and maintenance have also been prioritized in these models. The exterior surfaces are crafted from durable, easy-to-clean materials, while the interior features non-stick coatings that facilitate hassle-free cleaning. Additionally, features such as removable trays and racks allow for simplified upkeep, ensuring that the appliance remains in top condition over time.

User-friendly interfaces are another highlight, with intuitive controls that allow users of all skill levels to operate these appliances with ease. Digital displays provide clear information on cooking times and settings, enhancing the overall cooking experience.

In summary, the Kenmore 153.338003 and 153.338073 stand out in the market due to their effective features, advanced technologies, and practical characteristics. They represent a blend of innovation and convenience, making them an excellent addition to any modern kitchen.
Top Page Image Contents