IMPORTANT: Your dishwasher is designed to use a liquid rinse aid. The use of rinse aids greatly improves drying by allowing water to drain from the dishes after the final rinse. They also keep water from forming droplets that can dry as spots or streaks. Do not use a solid or bar-type rinse aid.

Filling the dispenser

The rinse aid dispenser holds 5 oz (150 mL) of rinse aid. Under normal conditions, this will last for about 1 to 3 months.

1.Make sure the dishwasher door is fully open.

2.Turn the dispenser knob to "Open" and lift it out.

 

\

 

USERINSEAIDFOR

/

 

 

B

 

 

Lock

 

_C

BETTERDRYING

 

 

 

k_

Add

 

A.....

A. Dispenser knob

B.Indicator

C. Indicator window

3= Pour rinse aid into the opening until the indicator points to "Full." Do not overfill. (When the rinse aid indicator drops to the "Add" level, add more rinse aid.)

4.Clean up any spilled rinse aid with a damp cloth.

5.Place the knob back into the opening and turn to the "Lock" position.

Rinse aid setting

The amount of rinse aid released into the final rinse can be adjusted. For most water conditions, the factory setting of 2 will give good results. If you have hard water or notice rings or calcium spots on your glasses or dishes, try a higher setting.

Lock

Open

To adjust the setting

1.Remove the dispenser knob.

2.Turn the arrow adjuster inside the dispenser to the desired setting by either using your fingers or inserting a flat-blade screwdriver into the center of the arrow and turning.

Full

Add

3. Replace the dispenser knob.

Hot water dissolves and activates the dishwashing detergent. Hot water also dissolves grease on dishes and helps glasses dry spot- free. For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Loads may not wash as well if the water temperature is too low. Water that is too hot can make some soils harder to remove and cause certain detergent ingredients not to function. If your water heater is located far from the dishwasher, it may be necessary to run the hot water at the faucet closest to the dishwasher to minimize the amount of cold water in the water line.

To check water temperature

1.Run hot water at the faucet closest to your dishwasher for at least 1 minute.

2.Place a candy or meat thermometer in a glass measuring cup.

3= Check the temperature on the thermometer as the water is running into the cup.

Additional efficiency tips

•To save water, energy and time, do not rinse dishes before putting them into the dishwasher.

•Use a delay feature to run your dishwasher during off-peak hours. Local utilities recommend avoiding heavy usage of energy at certain times of day.

•During the summer, run your dishwasher at night. This reduces daytime heat buildup in the kitchen.

•Use a rinse aid to improve drying.

•Use cycles or options that add extra heat to the wash or rinse portion of the cycle only when needed.

•If your home is equipped with a water softener, you may want to avoid starting the dishwasher during the regeneration of the softener, since this may contribute to poor wash performance.

10

Page 9 Page 11
Page 10
Image 10
Kenmore 665.13465, 665.13245, 665.77925 manual Filling the dispenser, To check water temperature, Additional efficiency tips
Page 9 Page 11

665.13475, 665.13455, 665.77925, 665.13245, 665.13465 specifications

The Kenmore 665 series, specifically models 1346, 1347, 1324, 1345, and 77925, exemplifies high performance and innovative features in modern dishwashers. Designed to cater to the demands of busy households, these models incorporate various technologies to enhance cleanliness, efficiency, and user experience.

One of the standout features of the Kenmore 665 series is its advanced cleaning system, which utilizes high-pressure wash arms and multiple spray levels. This ensures that water reaches every corner of the dishwasher, effectively removing tough stains and dried-on food particles. The enhanced cleaning performance is further supported by the targeted wash zones that allow users to customize the wash cycle according to their load requirements.

Energy efficiency is another key characteristic of the 665 series. With Energy Star certification, these dishwashers are designed to use water and energy judiciously, making them an eco-friendly choice for consumers. Their efficient use of resources not only helps in lowering utility bills but also contributes to a more sustainable home environment.

The quiet operation of the Kenmore 665 series is a significant advantage, with noise levels often measured below 50 dBA. This makes them ideal for open-concept living spaces or homes where peace and quiet are valued. The models are equipped with sound insulation features and a solid build that minimizes operational noise.

Flexibility is another hallmark of these dishwashers. Users can benefit from adjustable racks, allowing them to create the ideal space for larger items like pots and pans. The third rack feature available in some models offers additional space for utensils, maximizing capacity and ensuring thorough cleaning.

The control panel is designed for ease of use, featuring intuitive settings and cycles to choose from, including quick wash and sanitize options. The delay start feature adds convenience, allowing users to run the dishwasher at a time that best suits their schedule.

Overall, the Kenmore 665.1346, 665.1347, 665.1324, 665.1345, and 665.77925 models combine cutting-edge technology with user-friendly features. They provide a reliable solution for families seeking efficient dishwashing, all while maintaining an aesthetic appeal that fits seamlessly into modern kitchens. With a strong emphasis on performance and user satisfaction, the 665 series stands out as a choice for discerning consumers looking for quality and reliability in their kitchen appliances.
Top Page Image Contents