Kenwood KAC-PS4D, KAC-X4R 2WARNING, 2CAUTION, NOTE, FCC WARNING, FCC NOTE

Safety precautions

2WARNING

To prevent injury or fire, take the following precautions:

•Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.

•When extending the battery, or ground wires, make sure to use automotive- grade wires or other wires with the range of 10 mm2 (AWG 8) to 25 mm2 (AWG 4) to prevent wire deterioration and damage to the wire coating.

•To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.

•If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.

•Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.

2CAUTION

To prevent damage to the machine, take the following precautions:

•Be sure the unit is connected to a 12V DC power supply with a negative ground connection.

•Do not open the top or bottom covers of the unit.

•Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

•When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.

•To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

NOTE

•If you experience problems during installation, consult your Kenwood dealer.

•If the unit does not seem to be working right, consult your Kenwood dealer.

•Digital processing is performed inside this amplifier. Therefore, when used in conjunction with other amplifiers, there may be a slight delay. If this occurs, input the pre-output audio from this amplifier into the other amplifier.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

NOTE

This Class B digital apparatus complies with Canadian ICES-003.

Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems)

Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.

Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.

This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.

Cleaning the unit

If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.

2CAUTION

Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.

To prevent battery rise

When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.

Protection function

There is a Protection function installed in the unit to protect the unit and speakers from various problems. When Protection operates, the display informs you of the condition.

Display	Informations
"E-01"	When the inside of the unit is overheating.
	When the unit has failed and direct current voltage is generated to the speaker’s
	output.
"E-02"		NOTE
	Turn the power OFF and release the protection. If the "E-02" code does not disappear,
	contact your Kenwood dealer.
"E-03"	When the speaker cord is shorted.
"E-03"	When the speaker output is in contact with the vehicle ground.

	When a system error occurs.
"E-99"	Press the Reset button. If the "E-99" code does not disappear, contact your Kenwood
	dealer.
"VOLT" display is	When voltage gets out of operation range.
blinked.	When voltage gets out of operation range.
blinked.

Wiring

•Take the battery wire for this unit directly from the battery. If it’s connected to the vehicle’s wiring harness, it can cause blown fuses etc.

•If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire.

•Do not allow the wire to directly contact the edge of the iron plate by using Grommets.

•Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative - terminal. Do not turn the power on if the ground wire is not connected.

•Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger.

•For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit’s fuse capacity. (Use a power wiring cord with a diameter between 10 mm2 (AWG 8) to 25 mm2 (AWG 4).)

•When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.

Speaker Selection

•The rated input power of the speakers that are going to be connected should be greater than the maximum output power (in Watts) of the amplifier. Use of speakers having input power ratings that are less than the output power of the amplifier will cause smoke to be emitted as well as damage.

•The impedance of the speakers that are going to be connected should be 2Ω or greater (for stereo connections), or 4Ω or greater (for bridged connections). When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.

	4Ω
	4Ω	4Ω
	4Ω
8Ω	2 Ω
8Ω	2Ω

Combined impedance

2English