Kenwood Function settings, Item, [FUNCTION], [SETTINGS], [AUDIO CTRL], [AUDIO CTRL] :, Selectable setting (Preset: *)

Function settings

1Press the volume knob to enter [FUNCTION] mode.

2Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter.

3 Turn the volume knob to make a selection, then press to confirm.

See table below for selection.

Repeat step 3 until the desired item is selected/activated.

Press to return to the previous item. 4 Hold to finish the procedure.

[AUDIO CTRL] : While listening to any source except in STANDBY state...

Item		Selectable setting (Preset: *)
SUB-W LEVEL	–15 — +15 (Preset: 0): Adjusts the subwoofer output level.
BASS BOOST	B.BOOST LV1*/ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.
SYSTEM Q	NATURAL*/ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the
	music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS ADJUST	BASS C FRQ:	60/ 80/ 100*/ 200: Selects the center frequency.
	BASS LEVEL:	–8 — +8 (Preset: 0): Adjusts the level.
	BASS Q FCTR:	1.00*/ 1.25/ 1.50/ 2.00: Adjusts the Q factor.
	BASS EXTEND:	ON: Turns on the extended bass. ; OFF*: Cancels.
MID ADJUST	MID C FRQ:	0.5K/ 1.0K*/ 1.5K/ 2.5K: Selects the center frequency.
	MID LEVEL:	–8 — +8 (Preset: 0): Adjusts the level.
	MID Q FCTR:	0.75/ 1.00*/ 1.25: Adjusts the Q factor.
TRE ADJUST	TRE C FRQ:	10.0K/ 12.5K*/ 15.0K/ 17.5K: Selects the center frequency.
	TRE LEVEL:	–8 — +8 (Preset: 0): Adjusts the level.
BALANCE	L15 — R15 (Preset: 0): Adjusts the left and right speaker output balance.
FADER	R15 — F15 (Preset: 0): Adjusts the rear and front speaker output balance.
SUB-W SET	ON*: Turns on the subwoofer output. ; OFF: Cancels.
DETAIL SET	LPF SUB-W:	THROUGH*: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies
		higher than 85 Hz/ 120 Hz/ 160 Hz are cut off.
	SUB-W PHASE: REV (180°)/ NORM (0°)*: Selects the phase angle of the subwoofer output to be in line
		with the speaker output for optimum performance. (Selectable only if a setting other than
		[THROUGH] is selected for [LPF SUB-W].)
	SUPREME SET: ON*: Creates realistic sound by interpolating the high-frequency components that are lost
		in MP3/WMA audio compression. ; OFF: Cancels. (Selectable only when playback an MP3/
		WMA disc.)
	VOL OFFSET:	–8 — +8 (for AUX) ; –8 — 0 (for other sources): Presets the volume adjustment level of
	(Preset: 0)	each source. The volume level will automatically increase or decrease when you change the
		source. (Before making an adjustment, select the source you want to adjust.)

[SUB-W LEVEL/ SUB-W SET/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 7) [SUB-W LEVEL/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON].

Select a source before making a source tone memory adjustment, [BASS ADJUST/ MID ADJUST/ TRE ADJUST].

Continued...

ENGLISH

11