Troubleshooting Guide

The messages shown below display your systems condition.

EJECT:

• No disc magazine has been loaded in

 

the changer. The disc magazine is not

 

completely loaded.

 

• No CD in the unit.

NO DISC:

No disc has been loaded in the disc

 

magazine.

TOC ERR:

• No disc has been loaded in the disc

 

magazine.

 

• The CD is quite dirty. The CD is upside-

 

down. The CD is scratched a lot.

READ ERR:

• The number of files or folders which are

 

stored in the connected USB device is above

 

the limitation.

 

• The file system of the connected USB device

 

is broken.

 

➪ Copy the files and folders for the USB

 

device again referring to http://www.

 

kenwood.com/usb/. If the error message is

 

still displayed, initialize the USB device or

 

use other USB devices.

E-05:

The disc is unreadable.

BLANK:

Nothing has been recorded on the MD.

NO TRACK:

No tracks are recorded on the MD, although it

 

has a title.

NO PANEL:

The faceplate of the slave unit being

 

connected to this unit has been removed.

E-77:

The unit is malfunctioning for some reason.

 

➪ Press the reset button on the unit. If the

 

"E-77" code does not disappear, consult

 

your nearest service center.

E-99:

Something is wrong with the disc magazine.

 

Or the unit is malfunctioning for some reason.

 

➪ Check the disc magazine. And then press

 

the reset button on the unit. If the "E-99"

 

code does not disappear, consult your

 

nearest service center.

LOAD:

Discs are being exchanged in the Disc

 

changer.

READING:

The unit is reading the data on the disc.

HOLD:

The protective circuit in the unit activates

 

when the temperature inside the automatic

 

disc changer exceeds 60°C (140°F), stopping

 

all operation.

 

➪ Cool down the unit by opening the

 

windows or turning on the air conditioner.

 

As the temperature falls below 60°C

 

(140°F), the disc will start playing again.

IN (Blink):

The CD player section is not operating

 

properly.

 

➪ Reinsert the CD. If the CD cannot be

 

ejected or the display continues to flash

 

even when the CD has been properly

 

reinserted, please switch off the power

 

and consult your nearest service center.

PROTECT:

The speaker wire has a short-circuit or

 

touches the chassis of the vehicle, and then

 

the protection function is activated.

 

➪ Wire or insulate the speaker cable

 

properly and press the reset button. If

 

the "PROTECT" code does not disappear,

 

consult your nearest service center.

NA FILE:

An Audio file is played with a format that this

 

unit can’t support.

 

➪ ----

COPY PRO:

A copy-protected file is played.

 

➪ ----

DEMO:

The Demonstration mode has been selected.

 

➪ The <Demonstration mode Setting> (page

 

29) is ON. Turn it OFF.

NO DVICE:

The USB device is selected as a source

 

although no USB device is connected.

 

➪ Change the source to any source other

 

than USB. Connect an USB device, and

 

change the source to USB again.

NA DVICE:

An unsupported USB device is connected.

 

➪ For the supported USB devices, refer to

 

<http://www.kenwood.com/usb/>.

NO MUSIC/E-15:• The connected USB device contains no playable audio file.

•Media was played that doesn’t have data recorded that the unit can play.

USB ERR:

The connected USB device is rated a current

 

capacity higher than the allowable limit.

 

➪ Check the USB device with reference to

 

<http://www.kenwood.com/usb/>.

 

Some trouble may have occurred to the

 

connected USB device.

 

➪ Change the source to any source other

 

than USB. Remove the USB device.

iPod ERR:

Connection to the iPod has failed.

 

➪ Remove the USB device and then

 

reconnect it.

 

➪ Confirm that the software for the iPod is

 

the latest version.

REMOVE:

The Remove mode has been selected for the

 

USB device. You can remove the USB device

 

safely.

38 English