Surround speaker setting mode to the receiver is ON.
Surround speaker setting mode to the receiver is OFF.

Preparing for surround sound

Speaker settings

To enable you to obtain optimum enjoyment from the receiver’s listening modes, make sure to complete the speaker settings (subwoofer, front, center, and surround speakers) as described below.

MULTI CONTROL

SET UP

POWER ON/STANDBY

(KRF-V7050)

SET UP

MULTI

CONTROL

RC-R0613

RC-R0720

1Turn on the power to this receiver by pressing POWER ( ) key.2Select a speaker system.

1 Press the SET UP key such that the subwoofer setting indication “SUBW ON” appears.

 

SP

 

 

 

TI.VOL

 

 

 

FM

DIGITAL

 

 

 

 

A

 

L

C

R

 

 

 

 

 

 

 

MUTE

LFE

 

SW

AM PRO LOGIC S.DIRECT

 

 

 

 

 

 

 

 

MHz 3 STEREO MONITOR

 

 

 

RDS

 

EON

PTY

LS

S

RS

kHz DOWN MIX

DSP

 

 

 

TP

TA

NEWS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2Use the MULTI CONTROL knob or keys to select the appro- priate subwoofer setting.

1 SUBW ON: Subwoofer setting mode to the receiver is ON. 2 SUBW OFF: Subwoofer setting mode to the receiver is OFF.

•The initial setting is “SUBW ON”.

•When the setting “SUBW OFF” is selected, the front speakers are automatically set to “FRNT LRG” and the procedure skips to step 5.

•When subwoofer output sound is required, select “FRNT NML”.

3Press the SET UP key to accept the setting.

• The front speakers setting indication “FRNT” appears.

 

SP

 

 

 

TI.VOL

 

 

 

FM

DIGITAL

 

 

 

 

A

 

L

C

R

 

 

 

 

 

 

 

MUTE

LFE

 

SW

AM PRO LOGIC S.DIRECT

 

 

 

 

 

 

 

 

MHz 3 STEREO MONITOR

 

 

 

RDS

 

EON

PTY

LS

S

RS

kHz DOWN MIX

DSP

 

 

 

TP

TA

NEWS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4Use the MULTI CONTROL knob or keys to select the appropri- ate front speakers setting.

1 FRNT NML (normal): Average size front speakers are connected to the receiver.

2 FRNT LRG (large): Large front speakers are connected to the receiver.

•For “FRNT LRG” selection, no sound will be heard from SUBW even when it is set to ON. However, if you select CINEMA EQ when subwoofer is selected, you will be able to hear sound from the subwoofer.

When in STEREO mode, the sound goes directly to front speaker.

5Press the SET UP key to accept the setting.

19

6Use the MULTI CONTROL knob or keys to select the appropriate center speaker setting.

If you selected “LRG” as the front speakers setting,

1 CNTR LRG (large): A large center speaker is connected to the receiver.

2CNTR NML (normal): An average size center speaker is con-

 

nected to the receiver.

 

3 CNTR OFF:

Center speaker setting mode to the

Preparations

1 CNTR ON:

Center speaker setting mode to the receiver is

 

receiver is OFF.

 

If you have selected “NML” as the front speakers setting,

ON.

2 CNTR OFF: Center speaker setting mode to the receiver is OFF.

7Press the SET UP key again to accept the setting.

• The surround speaker setting indication “SURR” appears.

8Use the MULTI CONTROL knob or keys to select the appropriate surround speaker setting.

If you selected “LRG” as the center speaker setting,

1 SURR LRG (large): Large surround speakers are con-

nected to the receiver.

2SURR NML (normal): Average size surround speakers are connected to the receiver.

3SURR OFF: Surround speaker setting mode to the receiver is OFF.

If you have selected other than “LRG” as the center speaker setting,

1 SURR ON:

2 SURR OFF:

9Press the SET UP key again to accept the setting.

•The receiver enters the speaker volume level adjustment mode.

•In steps 3 and 4, indications appear only for the selected channels of the speakers that require adjusting.

3Adjust the speaker volume level.

From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same.

1Use the MULTI CONTROL knob or keys to adjust the volume level of the test tone output from the speaker channel to be adjusted.

The channel indication blinks while the test tone is being output.

SP

A

TI.VOL

L

C

R

FM

DIGITAL

 

 

MUTE

AM PRO LOGIC S.DIRECT

 

 

LFE

 

 

RDS

EON

PTY

 

 

MHz 3 STEREO MONITOR

LS

S

RS

kHz DOWN MIX

DSP

TP

TA

NEWS

 

 

 

 

 

The test tone is heard from the speakers in the following sequence for 2 seconds each:

•If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed.

•

•If the speaker setting selects are OFF, the speaker level settings are reset.

2Press the SET UP key.

•The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers.

Continued to next page

• The center speaker setting indication “CNTR” appears.