Kenwood KRF-V7050D, VR-507 Listening to radio broadcasts, station, Recording music in A-RECor M-RECmode, 4Use the MULTI CONTROL knob or keys to select the

Recording

Recording video

1Use the INPUT SELECTOR to select the video source (other than “VIDEO1”) you want to record.

2Set the video deck connected to VIDEO 1 to record.

• Select the REC MODE to record a digital input source.

3Start playback, then start recording.

• Recording may not be normal for some video software. This is due to

the copy guard condition. t

Recording audio (digital sources)

Switch on the REC mode to record a digital input source.

Usually use the A-REC(Auto-Record)mode to record audio input sources. When the digital mode changes during recording in the A-RECmode, the audio input source may be interrupted momentarily.

Recording music in A-REC or M-REC mode

DIMMER

INPUT SELECTOR

1Use the INPUT SELECTOR knob to select the source (CD/ DVD, DVD/6ch, VIDEO2 or VIDEO3) you want to record.

2Set the cassette deck or MD recorder to record.

3Press and hold the DIMMER key for more than 2 seconds to select the A-REC or M-REC mode.

•The mode changes every 2 seconds as shown below.

1 Rec mode off : The digital input record mode is switched off.

2A-REC :The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for

recording.

3 M-REC :The input signal type at the moment this mode is selected is held throughout this mode.

For A-REC mode:

			DIGITAL
	FM	AUTO SOUND
	AM PRO LOGIC S.DIRECT
	MHz 3 STEREO MONITOR
	kHz DOWN MIX		DSP
	FM	AUTO SOUND	DIGITAL			AUTO
	AM PRO LOGIC S.DIRECT					MEMO
	MHz 3 STEREO		MONITOR			ST.
	kHz DOWN MIX		DSP		TUNED
For M-REC mode:
	FM AUTO SOUND DIGITAL
	AM PRO LOGIC S.DIRECT
	MHz 3 STEREO MONITOR
	kHz DOWN MIX		DSP
	FM AUTO SOUND DIGITAL				AUTO
	AM PRO LOGIC S.DIRECT				MEMO
	MHz 3 STEREO		MONITOR			ST.
	kHz DOWN MIX		DSP	TUNED

4Start playback, then start recording.

•If the audio reproduction stops in the middle due to change in the input signals, etc., press the DIMMER key.

Listening to radio broadcasts

The receiver can store up to 40 stations in the memory and recall them by

one-touch operation. 23

Tuning radio stations

MULTI CONTROL

INPUT SELECTOR

BAND AUTO/CINEMA EQ

MULTI

CONTROL

BAND

AUTO

TUNER

	RC-R0613
RC-R0720	Operations

1Use the INPUT SELECTOR knob or TUNER key to select the tuner.2Use the BAND key to select the desired broadcast band.

Each press switches the band		“AM” or “FM” indicator
as follows:		appears in the display
	1 FM
		FM	DIGITAL	AUTO
	2 AM	AM PRO LOGIC S.DIRECT
		MHz 3 STEREO MONITOR
		kHz DOWN MIX	DSP

3Use the AUTO/CINEMA EQ. key to select the desired tuning method.

Each press switches the tuning method as follows:

1 AUTO lit (auto tuning)	“AUTO” indicator lights up
2 AUTO not lit (manual tuning)	in the display.
	FM	DIGITAL	AUTO
	AM PRO LOGIC S.DIRECT
	MHz 3 STEREO MONITOR
	kHz DOWN MIX	DSP

•Normally, set to “AUTO” (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning, stereo broadcasts will be received in monaural.)

4Use the MULTI CONTROL knob or keys to select thestation.

Frequency		“ST.” lights when a broadcast
display		is being received in stereo.
		FM	DIGITAL		AUTO
		AM PRO LOGIC S.DIRECT
		MHz 3 STEREO MONITOR			ST.
		kHz DOWN MIX	DSP	TUNED
	“TUNED” is displayed when a
	station is received.

Auto tuning :	The next station is tuned automatically.
Manual tuning :	Turn the knob (press the key) to select the
	desired station.