Listening to a source component

16

VOLUME CONTROL

INPUT SELECTOR

VIDEO AUDIO

VOLUME

1Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)) to select the source you want to listen to.

The input sources change as shown below:

Operations

Selecting a source using the INPUT SELECTOR knob

 

 

 

 

1 TUNER

 

 

 

 

2

"CD" ("CD"*)

 

3

"TAPE" or "MD" ("TAPE"*)

 

4

"PHONO"("PHONO"*)

 

5

"VIDEO1" ("VCR1"*)

 

6

"VIDEO2" ("VCR2"*)

 

 

7

"VIDEO3" ("VCR3"*)

 

 

Selecting a source using the AUDIO key on the remote control

1"CD" ("CD"*)

2"TAPE" or "MD" ("TAPE"*)

3 TUNER

4 "PHONO"("PHONO"*)

Selecting a source using the VIDEO key on the remote control

1 "VIDEO1" ("VCR1"*)

2 "VIDEO2" ("VCR2"*)

3 "VIDEO3" ("VCR3"*)

4 "<--->" (Not used by this receiver.)

* Once setup codes are registered in the remote control, the input name display changes according to the name of the registered component.

Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears

instead of "VIDEO 1".RC2

• When using the remote control after initial setup, any inputs that have not been registered with a setup code are deleted from the

cyclic list.

RC4

•The INPUT SELECTOR on the front panel of the receiver always cycles through all inputs.

2Start playback from the selected source.

3Use the VOLUME CONTROL (VOLUME) to adjust the volume.

Normal playback

KRF-V8010D (En/T)

Adjusting the sound

 

SOURCE DIRECT

VOLUME CONTROL

BASS BOOST

SOUND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PHONES

MULTI CONTROL

SPEAKERS A/B

VIDEO

MUTE

TUNING/SKIP VOLUME

SOUND

Adjusting the tone

If a source that is not Dolby Digital is selected, you can adjust the sound quality when the receiver is in the stereo mode.

1Press the SOUND key to select the tone mode to be adjusted.

BASS: Select this to adjust the low frequency range. (Press the SOUND key once.)

TREB: Select this to adjust the high frequency range. (Press the SOUND key twice.)

 

 

 

TREB+4

 

TUNED

SP A

L

R

 

 

AUTO

 

 

SW

 

 

MEMO.

 

 

 

STEREO

ST.

2Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound quality.

•The bass and treble levels are adjustable from -10 to +10 in 2 step increments.

•The adjustment item is displayed for approximately eight sec- onds.

•If you used the remote control to perform the above setting, press the VIDEO key at this point to turn off the remote control’s own adjustment mode. In this case, the input source is not switched.

Once-touch low frequency emphasis (bass boost)

If a source that is not Dolby Digital is selected, you can adjust the sound quality when the receiver is in the stereo mode.

Press the BASS BOOST key.

•Press the key once to select the maximum (+10) low frequency emphasis setting.

•This key does not function when the receiver is in the sound quality or ambience effects adjustment mode.

Switching back to the previous setting

Press the BASS BOOST key again.