Keurig Ultra B50 Set-Up & First Brew, Priming your Brewer, Ready to Brew your First Cup

Set-Up & First Brew

IMPORTANT: You cannot use your Keurig brewer until it has been primed for its first use as set forth below.

NOTE: If Brewer has been exposed to tempera- tures below freezing, allow Brewer at least two hours to reach room temperature before prim- ing. A frozen or extremely cold brewer will not prime properly and can cause damage.

Priming your Brewer

1.Unwrap cord and plug the brewer into a grounded outlet.

2.Place a cup or mug on the Drip Tray Plate.

3.Remove the Water Reservoir from Brewer by first removing Lid from Reservoir, then lifting Reservoir straight up and away from Brewer (may be tight). Rinse with fresh water.

4.Fill Water Reservoir with fresh water so that the water level reaches the top edge of the clear viewing area. (Be careful not to over fill.)

5.Place Water Reservoir base into the left side of the Brewer and be sure the Water Reservoir Lock Tabs engage with the Brewer. Replace Lid on Water Reservoir.

6.Press Power Button found on upper right panel of the Brewer. The green light surround- ing the Power Button will become illuminated.

7.The LCD Control Center will come on and indicate ‘PRIME’ and the icon for the Large Cup will flash. If 'NOT READY' appears in

LCD Control Center, be sure the handle is all the way down. Please note, a K-Cup should not be used for the Priming Sequence.

Large Cup

Icon

PRIME

Large

Cup

Button

Power

Button

8.Press the Large Cup Button below the flashing Large Cup indicator.

NOTE: If the Water Reservoir is empty or not in place on the Brewer, then the LCD Control Center will also indicate ‘ADD WATER’. None of the buttons will be activated until water is added to the Water Reservoir.

9.The Brewer will automatically fill the Brewer (priming it) and then the water will be heated. This will take about 3 minutes. During the heating period 'NOT READY' is dis- played on the LCD Control Center. When the water is heated, 'READY' will be displayed.

NOTE: You may see small amounts of water coming from the Vent and dripping into the Water Reservoir during this and subsequent heating – this is normal.

10.Press the Large Cup Button below the flashing Large Cup Icon to start a cleansing brew, during which hot water will flow into your cup or mug. Pour the hot water into the sink.

11.The Brewer may take 15 seconds to reheat water between brews and then 'READY' will again be displayed.

12.The one-time priming process is now complete and you are ready to brew!

Ready to Brew your First Cup

K-Cup®Handle portion pack

K-Cup

Chamber

1.LCD Control Center will indicate ‘READY’.

2.Place a cup or mug on the Drip Tray Plate.

3.Lift the Handle and the K-Cup Holder will open toward you.

CAUTION: There are two sharp needles that puncture the K-Cup®portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Chamber.

4. Select a K-Cup®portion pack.

NOTE: Do not remove the foil lid or puncture the K-Cup®portion pack.

5.Place a K-Cup®portion pack in the K-Cup Holder (as shown in exhibit at top of page).

6.Lower the Handle to close the Lid over the K-Cup Holder, (when it is closed completely, the LCD Control Center will indicate ‘BREW’ and the large and small cup icons will blink up to 60 seconds).

Small Cup	BREW	Large Cup
		MENU

7.Choose the amount of coffee or tea you wish to brew by pressing the button under the Small Cup or Large Cup Icon that indicates your choice. The Large Cup choice will yield a 7.25 oz serving and

the Small Cup choice will yield a 5.25 oz serving.

NOTE: If you do not push the Brew Buttons in 60 seconds, the LCD Control Center will return to ‘READY’ and the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew Buttons by raising and lowering the Handle completely.

8.The LCD will now display the word ‘BREWING’ and the serving size you selected.

BREWING

CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Chamber during the brew process.

9.There may be a short pause before the brewing process begins. The process lasts for approximately 40 seconds and ends with a burst of air to remove all liquid coffee or tea from the K-Cup.

10.Lift the Handle and remove and dispose of the used K-Cup.

CAUTION: K-Cup will be hot.

11.Enjoy your first cup of Keurig Brewed® gourmet coffee or tea!

12.Your Brewer may display ‘NOT READY’ as it heats water for the next brew cycle. The ‘READY’ indication will return to the LCD Control Center in approximately 15 seconds.

NOTE: Following the brew, your Brewer will fill to be ready for the next brew. The pump will make a vibrating sound. This is normal.

6 7