4.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

5.Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Connectthe Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut onto the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1 - Connection to Water Valve

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

A

B

C

D

A. Tube clamp

C. Compression nut

B. Copper tubing

D. Valve inlet

6.The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2 - Connection to Water Line

1.Unplug refrigerator or disconnect power.

2.Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.

3.If the gray water tube supplied with the refrigerator is not long enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A

B

C

D

E F G

A. Refrigerator water tubing

 

E. Ferrule (purchased)

B. Nut (provided)

 

 

F. Nut (purchased)

C. Bulb

 

 

 

G. Household water line

D. Coupling (provided)

 

 

 

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

8

Page 7 Page 9
Page 8
Image 8
KitchenAid 2318581 manual Connectthe Water Supply, Connect to Water Line, Style 2 Connection to Water Line
Page 7 Page 9

2318581 specifications

The KitchenAid 2318581 is an innovative stand mixer attachment designed to enhance the functionality of KitchenAid stand mixers. This attachment is specifically engineered for users who want to broaden their culinary capabilities without investing in additional appliances. The 2318581 attachment brings several main features that cater to both casual cooks and professional chefs alike.

One of the standout characteristics of the KitchenAid 2318581 is its versatility. It is compatible with a wide range of KitchenAid stand mixer models, allowing users to easily connect it to their existing equipment. This means that home chefs can take advantage of the powerful motor and multiple speed settings of their stand mixer, making food preparation more efficient and enjoyable.

The design of the 2318581 attachment is also noteworthy. It is crafted from durable materials that ensure longevity and reliable performance over time. The sleek and modern aesthetic not only fits seamlessly into any kitchen décor but also provides ease of use in terms of attachment and detachment.

In terms of technology, the KitchenAid 2318581 offers a user-friendly interface. Its simple design allows for quick and hassle-free setup, ensuring that users can start creating delicious dishes with minimal delay. This attachment also features multiple operating speeds, providing precision control for various food processing needs, from mixing dough to making sauces and purees.

Another notable technology in this attachment is the integrated safety mechanism. It is designed to operate safely without risk of accidental disconnection while in use, ensuring that users can focus on their cooking without distractions or worries about equipment failure.

The KitchenAid 2318581 is ideal for those who want to streamline their cooking processes, reduce preparation time, and achieve consistent results every time. It transforms the stand mixer into a multifunctional kitchen tool, making it easier to experiment with new recipes and techniques.

In conclusion, the KitchenAid 2318581 is a must-have accessory for any KitchenAid stand mixer owner looking to elevate their culinary experience. With its robust features, advanced technologies, and thoughtful design, it stands out as an essential tool for both novice and experienced cooks alike.
Top Page Image Contents